1. ఉత్పత్తి ముగిసిందిview
The Tamiya 86005 Black Paint Spray is specifically formulated for decorating transparent polycarbonate bodies used in R/C car modeling. This paint provides a durable, oil-resistant finish suitable for both electric and gas-powered R/C bodies.
Image 1.1: Tamiya 86005 Black Paint Spray can. This 100ml aerosol can contains black, gloss-finish paint designed for polycarbonate surfaces.
ముఖ్య లక్షణాలు:
- Black colored paint.
- Intended for polycarbonate R/C bodies.
- Can be used on gas-powered R/C bodies.
- Impervious to oil and fuels.
- Gloss finish.
- నీటి నిరోధకత.
2. భద్రతా సమాచారం
హెచ్చరిక: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm (Proposition 65 warning). Always use in a well-ventilated area. Keep out of reach of children. Read all warnings on the product label before use.
- Use only in a well-ventilated area. Avoid breathing vapors.
- చేతి తొడుగులు మరియు కంటి రక్షణ వంటి తగిన వ్యక్తిగత రక్షణ పరికరాలను ధరించండి.
- వేడి, వేడి ఉపరితలాలు, స్పార్క్స్, ఓపెన్ ఫ్లేమ్స్ మరియు ఇతర జ్వలన మూలాల నుండి దూరంగా ఉంచండి. స్మోకింగ్ లేదు.
- ఒత్తిడితో కూడిన కంటైనర్: ఉపయోగించిన తర్వాత కూడా కుట్టవద్దు లేదా కాల్చవద్దు.
- బహిరంగ మంట లేదా ఇతర జ్వలన మూలంపై స్ప్రే చేయవద్దు.
- సూర్యకాంతి నుండి రక్షించండి. 50°C (122°F) కంటే ఎక్కువ ఉష్ణోగ్రతలకు గురికావద్దు.
- స్థానిక నిబంధనలకు అనుగుణంగా కంటెంట్లు/కంటైనర్ను పారవేయండి.
- Note: Never use these paints on plastic models other than polycarbonate.
3. తయారీ మరియు సెటప్
3.1 కార్యస్థల తయారీ
- Ensure your workspace is clean, dust-free, and well-ventilated.
- Cover surrounding areas to protect them from overspray.
- Maintain an ambient temperature between 20-25°C (68-77°F) for optimal results.
3.2 ఉపరితల తయారీ
- Clean the polycarbonate R/C body thoroughly with mild soap and water to remove any dirt, grease, or mold release agents.
- Rinse the body completely and allow it to dry fully.
- For best adhesion, lightly scuff the inside surface of the polycarbonate body with a fine-grit abrasive pad (optional, but recommended for maximum durability).
- Mask off any areas you do not wish to paint using painter's tape or liquid mask. Remember to paint the body from the inside.
3.3 Paint Can Preparation
- Shake the can vigorously for at least one minute after the mixing ball begins to rattle. Continue shaking periodically during application.
- Test spray on a scrap piece of polycarbonate or similar material to check spray pattern and color consistency.
4. ఆపరేటింగ్ సూచనలు (అప్లికేషన్)
- Hold the Can: Hold the spray can upright, approximately 30 cm (12 inches) from the surface of the polycarbonate body.
- Apply Light Coats: Apply the paint in thin, even coats. It is better to apply several thin coats than one thick coat to prevent runs and ensure proper adhesion.
- ఓవర్లాప్ స్ట్రోక్లు: Begin spraying off the edge of the body and move across the surface in smooth, overlapping strokes. Release the nozzle at the end of each stroke.
- కోట్లు మధ్య ఎండబెట్టడం: Allow each coat to dry to the touch before applying the next. This typically takes 10-15 minutes, depending on humidity and temperature.
- Build Color: Continue applying thin coats until the desired color depth and opacity are achieved. For black, this may require 2-3 coats.
- క్యూరింగ్: After the final coat, allow the paint to cure completely. The full cure time is approximately 24 hours. Avoid handling the painted body excessively during this period.
- Remove Masking: Once the paint is dry to the touch, carefully remove any masking tape or liquid mask.
ముఖ్యమైన: Always paint the లోపల of the transparent polycarbonate body. This protects the paint from scratches and impacts during use.
5. నిర్వహణ మరియు నిల్వ
5.1 Can Maintenance
- After each use, invert the can and spray for a few seconds until only clear propellant comes out. This clears the nozzle and prevents clogging.
- Wipe the nozzle clean with a cloth.
5.2 నిల్వ
- Store the paint can in a cool, dry place, away from direct sunlight and extreme temperatures.
- Ensure the cap is securely placed on the can to prevent accidental discharge or drying of the nozzle.
- పిల్లలు మరియు పెంపుడు జంతువులకు దూరంగా ఉంచండి.
6. ట్రబుల్షూటింగ్
| సమస్య | సాధ్యమైన కారణం | పరిష్కారం |
|---|---|---|
| Uneven spray pattern / Clogging | Nozzle is clogged or paint not mixed properly. | Shake can vigorously. Clean nozzle by inverting can and spraying until clear, or by carefully removing and cleaning with a solvent (e.g., lacquer thinner). |
| పెయింట్ జారిపోతుంది లేదా చుక్కలుగా పోతుంది | Too much paint applied in one coat, or can held too close. | Apply thinner, even coats. Maintain a distance of 30 cm (12 inches) from the surface. |
| Poor adhesion / Peeling paint | Surface not properly cleaned or prepared. Not for use on non-polycarbonate plastics. | Ensure surface is clean, dry, and free of contaminants. Confirm the material is polycarbonate. |
| Dull finish | Insufficient coats or improper drying conditions. | Apply additional thin coats. Ensure proper ventilation and temperature during drying. |
7. స్పెసిఫికేషన్లు
| బ్రాండ్: | తమియా |
| మోడల్ సంఖ్య: | 86005 (TAM86005) |
| రంగు: | నలుపు |
| ముగించు రకం: | గ్లోస్ |
| అంశం వాల్యూమ్: | 100 మిల్లీలీటర్లు (3.38 Fl Oz) |
| పెయింట్ రకం: | Oil, Spray |
| నిర్దిష్ట ఉపయోగాలు: | R/C Car Polycarbonate Bodies |
| ఉపరితల సిఫార్సు: | Plastic (Polycarbonate only) |
| ఇండోర్/అవుట్డోర్ వినియోగం: | Indoor (with proper ventilation) |
| పూర్తి నివారణ సమయం: | 24 గంటలు |
| కవరేజ్: | 0.1 to 0.15 square meters per coat |
| నీటి నిరోధకత: | వాటర్ రెసిస్టెంట్ |
| UPC: | 885109209505 |
8. వారంటీ మరియు మద్దతు
వారంటీ: This product is sold without a manufacturer's warranty. Please refer to the product packaging for any specific warranty information that may be provided by the retailer at the time of purchase.
కస్టమర్ మద్దతు: For technical assistance or product inquiries, please contact Tamiya customer support directly through their official website or authorized distributors. Keep your product model number (86005) handy when contacting support.