Raspberry Pi Compute Module 3+ Lite User Manual

1. పరిచయం

The Raspberry Pi Compute Module 3+ Lite is an industrial-grade System-on-Module (SoM) that integrates the core components of a Raspberry Pi 3 Model B+ into a compact SODIMM form factor. This module is designed for embedded applications, offering a powerful quad-core processor and 1GB of LPDDR2 SDRAM. It provides access to more GPIO pins when used with a compatible I/O board (not included), making it suitable for a wide range of industrial and consumer products.

2. భద్రతా సమాచారం

Please read all safety instructions carefully before using the Raspberry Pi Compute Module 3+ Lite.

• The Compute Module must only be handled in compliance with Electrostatic Discharge (ESD) protection measures.
• Before connecting to a power supply, ensure that no thermal overload will occur. Adequate ventilation is crucial.
• Do not operate the module in humid, wet, or excessively dusty environments.
• Never allow direct contact with water or any other conductive liquids.
• Only connect the module with recommended power supplies that provide the correct voltagఇ మరియు ప్రస్తుత.
• Liquids, dust, and overvoltages can lead to dangerous situations or cause permanent defects.
• Avoid storing the module in an enclosed housing without proper ventilation to prevent damage or corrosion.
• Do not attempt to repair defective modules or components yourself. Unauthorized repairs can void your warranty and cause further damage.
• Recycle defective or discarded Compute Modules according to local electronic waste disposal regulations.

3. ఉత్పత్తి ముగిసిందిview

The Raspberry Pi Compute Module 3+ Lite offers a compact and robust solution for embedded systems. Its design allows for integration into custom hardware, leveraging the extensive Raspberry Pi ecosystem.

ముఖ్య లక్షణాలు:

• ప్రాసెసర్: Broadcom BCM2837B0, Cortex-A53 (ARMv8) 64-bit SoC running at 1.2GHz.
• RAM: 1GB of LPDDR2 SDRAM.
• ఫారమ్ ఫ్యాక్టర్: Based on the SODIMM standard, enabling use with standard connectors.
• GPIO: Provides access to a greater number of GPIO pins compared to standard Raspberry Pi boards when used with an appropriate I/O board.

మాడ్యూల్ లేఅవుట్:

మూర్తి 3.1: ముందు view of the Raspberry Pi Compute Module 3+ Lite, showing the main processor and memory components.

మూర్తి 3.2: వెనుకకు view of the Raspberry Pi Compute Module 3+ Lite, illustrating the SODIMM connector and additional circuitry.

4. సెటప్

The Compute Module 3+ Lite requires a compatible I/O board for operation. This section outlines the general steps for initial setup.

1. Prepare I/O Board: Ensure your I/O board is compatible with the Compute Module 3+ Lite and has the necessary power supply and peripheral connections.
2. Insert Compute Module: Carefully align the Compute Module 3+ Lite with the SODIMM connector on your I/O board. Apply even pressure to insert it fully until it is securely seated.
3. పెరిఫెరల్స్ కనెక్ట్ చేయండి: Connect any required peripherals such as a display (HDMI), keyboard, mouse, and network cable to the I/O board.
4. విద్యుత్ సరఫరా: Connect a suitable power supply to your I/O board. Refer to your I/O board's documentation for specific power requirements.
5. ఆపరేటింగ్ సిస్టమ్: The Compute Module 3+ Lite does not have onboard eMMC storage. You will need to provide an operating system via an SD card (if your I/O board supports it) or network boot. It is compatible with NOOBS 3.0.0 or later.

5. ఆపరేటింగ్ సూచనలు

Once the Compute Module 3+ Lite is set up with an I/O board and an operating system, its operation is similar to a standard Raspberry Pi.

• పవర్ ఆన్: Apply power to the I/O board. The module should boot up, and you should see output on your connected display.
• OS ఇంటరాక్షన్: Interact with the operating system using your connected keyboard and mouse.
• సాఫ్ట్‌వేర్ ఇన్‌స్టాలేషన్: Install software and applications as needed for your specific project or application.
• GPIO వినియోగం: Utilize the GPIO pins for interfacing with external hardware, following the documentation for your I/O board and the Raspberry Pi GPIO libraries.
• షట్‌డౌన్: Always perform a proper shutdown of the operating system before disconnecting power to prevent data corruption.

6. నిర్వహణ

Proper maintenance ensures the longevity and reliable operation of your Compute Module 3+ Lite.

• శుభ్రముగా ఉంచు: Regularly clean the module and I/O board to prevent dust accumulation, which can lead to overheating or short circuits. Use a soft, dry brush or compressed air.
• పర్యావరణ నియంత్రణ: Operate the module within its specified temperature and humidity ranges. Avoid extreme conditions.
• ఫర్మ్‌వేర్ నవీకరణలు: Keep the operating system and any relevant firmware updated to ensure optimal performance and security.
• సురక్షిత కనెక్షన్లు: Periodically check all connections (SODIMM, power, peripherals) to ensure they are secure and free from corrosion.
• ESD రక్షణ: When handling the module, always observe ESD precautions to prevent damage from static electricity.

7. ట్రబుల్షూటింగ్

ఈ విభాగం మీరు ఎదుర్కొనే సాధారణ సమస్యలకు పరిష్కారాలను అందిస్తుంది.

• పవర్ లేదు/బూట్ లేదు:
  • Ensure the power supply is correctly connected and provides sufficient voltage and current for the I/O board and module.
  • Verify the Compute Module is correctly seated in the SODIMM slot.
  • Check for any visible damage to the module or I/O board.
• డిస్ప్లే అవుట్‌పుట్ లేదు:
  • Confirm the display cable (e.g., HDMI) is securely connected to both the I/O board and the monitor.
  • మానిటర్ ఆన్ చేయబడిందని మరియు సరైన ఇన్‌పుట్ సోర్స్‌కు సెట్ చేయబడిందని నిర్ధారించుకోండి.
  • Verify that the operating system image is correctly installed and configured for display output.
• Peripheral Issues (Keyboard/Mouse/USB):
  • Try connecting peripherals to different USB ports on the I/O board.
  • Test peripherals with another device to confirm they are functional.
  • Ensure the operating system has the necessary drivers.
• వేడెక్కడం:
  • Ensure adequate ventilation around the module and I/O board.
  • Consider adding a heatsink or fan if operating in high-temperature environments or under heavy load.
  • Reduce CPU load if possible.

8. స్పెసిఫికేషన్లు

9. వారంటీ మరియు మద్దతు

For warranty information and technical support, please contact Raspberry Pi directly.

తయారీదారు సమాచారం:

Raspberry Pi Ltd.
194 Cambridge Science Park, Milton Road
GB - CB4 0AB Cambridge
ఇమెయిల్: compliance@raspberrypi.com
Webసైట్: https://www.raspberrypi.com

WEEE సంఖ్య: 20453810

Responsible Person for the EU:

Raspberry Pi Ireland Limited
3 Dublin Landings
IE - D01 C4E0 North Wall Quay, Dublin 1
ఇమెయిల్: compliance@raspberrypi.com
Webసైట్: https://www.raspberrypi.com