Secura Chainsaw Chains for Einhell RBK 3735 - Instruction Manual

1. ఉత్పత్తి ముగిసిందిview

This manual provides instructions for the installation, operation, and maintenance of your Secura square-chisel chainsaw chains, designed for the Einhell RBK 3735 chainsaw. These high-quality chains are engineered for durability and efficient cutting performance.

• Professional and high-quality Secura chain.
• Square-chisel design for effective cutting.
• Long service life and easy to sharpen.

Figure 1: Two Secura square-chisel chainsaw chains, ready for installation.

2. Important Information & Safety

ముఖ్యమైనది:

Chainsaw chains are specific to chainsaw models. It is crucial to select the correct chain for your Einhell RBK 3735. Chainsaws can have different cutting sets, and both the total length and cutting length can vary. Additionally, different chain systems (with large or small saw teeth) exist, which require specific drive sprockets.

To ensure compatibility, it is highly recommended to:

• Count the drive links on your existing chain.
• Determine the pitch of your existing chain (e.g., 3/8" or 0.325").
• Measure the groove width of the drive links (e.g., 1.3mm).

Always wear appropriate personal protective equipment (PPE) including safety glasses, gloves, and hearing protection when handling or installing chainsaw chains.

3. Installation & Chain Selection

3.1 Measuring Cutting Length

The 'cutting length' refers to the effective cutting area of the chain and bar. It is measured from the chainsaw's housing to the tip of the guide bar when the chain is mounted. This is not the total length of the chain itself, which will always be longer.

Figure 2: Correct method for measuring the cutting length of a chainsaw bar. The measurement is taken from the chainsaw body to the end of the guide bar, not the full length of the bar itself.

3.2 Identifying Chain Specifications

To ensure you have the correct replacement chain, identify the following specifications from your existing chain or chainsaw manual:

• పిచ్: The distance between three consecutive rivets divided by two. Common pitches are 3/8" LP (Low Profile) or 0.325".
• డ్రైవ్ లింక్‌లు: The number of links on the chain that fit into the guide bar groove. Count these carefully.
• గేజ్: The thickness of the drive links, which must match the groove width of your guide bar. Common gauges are 1.1mm, 1.3mm, or 1.5mm.

Figure 3: Visual guide to measuring key chainsaw chain specifications: Pitch, Drive Links, and Chain Gauge.

3.3 సాధారణ సంస్థాపనా దశలు

1. మొదటి భద్రత: Ensure the chainsaw is turned off, unplugged (electric) or spark plug cap removed (gas), and cool before beginning installation.
2. పాత గొలుసును తీసివేయండి: బార్ నట్లను విప్పు మరియు క్లచ్ కవర్‌ను తీసివేయండి. పాత గొలుసు మరియు గైడ్ బార్‌ను జాగ్రత్తగా తొలగించండి.
3. శుభ్రమైన భాగాలు: Clean any sawdust, debris, or old oil from the guide bar groove, sprocket, and clutch area.
4. కొత్త గొలుసును ఇన్‌స్టాల్ చేయండి: Place the new chain around the clutch sprocket and then guide it into the groove of the guide bar. Ensure the cutting edges of the chain are facing the correct direction (usually forward on the top of the bar).
5. Reattach Bar and Cover: Slide the guide bar back into position, ensuring the chain tension pin engages with the hole in the bar. Replace the clutch cover and hand-tighten the bar nuts.
6. చైన్ టెన్షన్‌ను సర్దుబాటు చేయండి: Adjust the chain tension screw until the chain is snug against the bottom of the guide bar, but can still be pulled freely by hand. There should be no sag on the underside of the bar. Tighten the bar nuts securely.
7. లూబ్రికేషన్ తనిఖీ చేయండి: Ensure the oil reservoir is filled with appropriate chain oil.

4. ఆపరేషన్

ప్రతి ఉపయోగం ముందు, కింది తనిఖీలను చేయండి:

• చైన్ టెన్షన్: Verify that the chain tension is correct. A properly tensioned chain should be snug but still able to be pulled around the bar by hand.
• చైన్ లూబ్రికేషన్: Ensure the chainsaw's oil reservoir is adequately filled with chain oil to prevent premature wear of the chain and guide bar.
• భద్రతా సామగ్రి: Always wear appropriate personal protective equipment, including a helmet with face shield, hearing protection, safety glasses, heavy-duty gloves, and chainsaw protective trousers/chaps.

Operate the chainsaw according to the manufacturer's instructions for your specific chainsaw model.

5. నిర్వహణ

Regular maintenance extends the life of your chainsaw chain and ensures optimal cutting performance.

5.1 పదునుపెట్టడం

The Secura square-chisel chains are designed to be easy to sharpen. Sharpen the chain regularly to maintain cutting efficiency. Refer to your chainsaw manual or a professional guide for the correct sharpening angles and file size for a 3/8" LP pitch chain.

5.2 శుభ్రపరచడం

ప్రతి ఉపయోగం తర్వాత, గొలుసు మరియు గైడ్ బార్‌ను శుభ్రం చేసి, సాడస్ట్, రెసిన్ మరియు చెత్తను తొలగించండి. ఇది పనితీరుకు ఆటంకం కలిగించే మరియు అరిగిపోయేలా చేసే పేరుకుపోవడాన్ని నివారిస్తుంది.

5.3 సరళత

Ensure continuous and adequate lubrication during operation. Check the oiler function regularly. When storing the chain, apply a light coat of oil to prevent rust.

5.4 తనిఖీ

Periodically inspect the chain for signs of wear, damage, or stretched links. Replace the chain if any damage is found or if it becomes excessively worn or stretched.

6. ట్రబుల్షూటింగ్

7. ఉత్పత్తి లక్షణాలు

8. వారంటీ మరియు మద్దతు

For warranty information or technical support regarding your Secura chainsaw chains, please refer to the documentation provided with your purchase or contact Secura customer service directly. Ensure you have your product model number (6361461) available when seeking support.