OONO D-1437 2-Channel Rocker Switch Thermal Circuit Breaker User Manual

1. ఉత్పత్తి ముగిసిందిview

The OONO D-1437 is a 2-channel power distribution module featuring rocker switch thermal circuit breaker overload protectors. Designed for DIN rail mounting, this module provides protection against overcurrent conditions for electrical circuits. Each channel includes a 10A thermal circuit breaker, allowing manual control of the output state (RESET or OFF) and indicating normal operation with a built-in red light.

2 కీ ఫీచర్లు

• ఇన్పుట్ వాల్యూమ్tage: AC 125V to 250V, 50-60Hz.
• Maximum Total Input Current: 20A (per position terminal block).
• గరిష్ట అవుట్‌పుట్ కరెంట్: 10A per channel.
• Maximum Total Output Current: 20 ఎ.
• సర్క్యూట్ బ్రేకర్లు: Two 10A rocker switch thermal circuit breaker overload protectors.
• స్విచ్ ఫంక్షనాలిటీ: Manual RESET or OFF states with integrated red indicator light for normal output.
• టెర్మినల్ బ్లాక్‌లు: Pitch 7.62mm (0.3 inch), suitable for 26AWG to 10AWG (4.0mm square) wires.
• DIN రైలు మౌంట్: High-quality fireproof nylon material carrier, compatible with 35mm, 32mm, and 15mm DIN rails.
• నిర్మాణం: FR-4 fiberglass dual copper layers PCB.

3. సాంకేతిక లక్షణాలు

4. భద్రతా సమాచారం

హెచ్చరిక: Electrical shock hazard. Installation and servicing should only be performed by qualified personnel. Always disconnect power at the main circuit breaker or fuse box before installing or servicing this device.

• అన్ని వైరింగ్‌లు స్థానిక మరియు జాతీయ విద్యుత్ కోడ్‌లకు అనుగుణంగా ఉన్నాయని నిర్ధారించుకోండి.
• పేర్కొన్న వాల్యూమ్‌ని మించకూడదుtage మరియు పరికరం యొక్క ప్రస్తుత రేటింగ్‌లు.
• Verify proper wire gauge for the current load to prevent overheating.
• Ensure secure connections at all terminal blocks to prevent loose contacts and potential hazards.
• This device is designed for indoor use in dry environments. Avoid exposure to moisture or extreme temperatures.

5. సెటప్ మరియు ఇన్‌స్టాలేషన్

5.1 DIN రైలు మౌంటు

The OONO D-1437 module is designed for easy installation on standard DIN rails (35mm, 32mm, or 15mm width). To mount, align the module's clips with the DIN rail and press firmly until it snaps into place. To remove, gently pull the release mechanism (if present) or pry the module off the rail.

5.2 వైరింగ్ కనెక్షన్లు

Refer to the schematic and connection diagrams for proper wiring. Ensure power is disconnected before making any connections.

• ఇన్పుట్ టెర్మినల్స్: Connect the AC 125-250V power supply to the input terminals labeled 'N' (Neutral) and 'L' (Line). The module supports a maximum total input current of 20A.
• అవుట్‌పుట్ టెర్మినల్స్: Each channel has 'L' and 'N' output terminals. Connect your load to the corresponding output channel. Each channel supports a maximum output current of 10A. The maximum total output current for the module is 20A.
• వైర్ స్పెసిఫికేషన్స్: Use wires within the range of 26AWG to 10AWG (4.0mm²). Strip wire insulation approximately 8mm before inserting into the terminal blocks. Tighten M3 screws securely.

5.3 కొలతలు

For precise integration into your electrical panel, refer to the detailed dimensional drawing below.

5.4 సంస్థాపన ముగిసిందిview వీడియో

Watch this video for a visual guide on the product's features and installation process.

6. ఆపరేటింగ్ సూచనలు

The OONO D-1437 features two independent rocker switches, each controlling one output channel.

• ON/RESET Position: When the rocker switch is pressed to the 'RESET' side, the circuit breaker is closed, allowing power to flow to the connected load. A built-in red indicator light will illuminate when the output is normal.
• ఆఫ్ స్థానం: When the rocker switch is pressed to the 'OFF' side, the circuit breaker is open, disconnecting power to the connected load. The red indicator light will be off.
• ఓవర్‌లోడ్ రక్షణ: In the event of an overcurrent, the thermal circuit breaker will automatically trip, moving the rocker switch to the 'OFF' position and disconnecting the load to prevent damage. To reset after an overload, allow a brief cooling period, then manually press the switch to the 'RESET' position. If the breaker trips repeatedly, investigate the cause of the overload.

7. నిర్వహణ

The OONO D-1437 is designed for minimal maintenance. However, periodic inspection is recommended to ensure optimal performance and safety.

• శుభ్రపరచడం: Ensure the module is free from dust and debris. Use a dry, soft cloth for cleaning. Do not use liquid cleaners or solvents.
• కనెక్షన్ తనిఖీ: Periodically inspect all wire connections to ensure they remain tight and secure. Loose connections can lead to overheating or intermittent operation.
• దృశ్య తనిఖీ: Check for any signs of physical damage, discoloration, or burning on the module or wiring. Replace the unit immediately if any damage is observed.

8. ట్రబుల్షూటింగ్

• లోడ్ చేయడానికి శక్తి లేదు:
  • Check if the rocker switch is in the 'RESET' position.
  • Verify that the input power supply is active.
  • అన్ని వైరింగ్ కనెక్షన్లు వదులుగా ఉన్నాయా లేదా దెబ్బతిన్నాయా అని తనిఖీ చేయండి.
• Circuit Breaker Trips Repeatedly:
  • This indicates an overcurrent condition. Disconnect the load and check for short circuits or excessive current draw.
  • Ensure the connected load does not exceed the 10A rating of the individual channel or the 20A total rating of the module.
  • Allow the breaker to cool down before attempting to reset.
• Indicator Light Not On:
  • The indicator light illuminates when the output is normal and the switch is in the 'RESET' position. If it's off, check the switch position, input power, and load connection.
  • If the breaker has tripped, the light will be off.

9. వారంటీ మరియు మద్దతు

For warranty information and technical support, please refer to the documentation provided at the time of purchase or contact the manufacturer directly. Keep your purchase receipt as proof of purchase.