GODIYMODULES Dual NE5532 Preamplifier బోర్డ్ ఇన్స్ట్రక్షన్ మాన్యువల్

పరిచయం

This manual provides essential information for the proper setup, operation, and maintenance of your GODIYMODULES Dual NE5532 Preamplifier Board. This pre-amplifier is designed with two NE5532 operational amplifiers, dedicating one amplifier per channel for enhanced audio performance compared to single operational amplifier designs. It features a built-in single power supply to dual power supply chip, allowing it to function with a single power input while providing dual power supply characteristics internally. The board incorporates large-capacity filter capacitors and a rectifier circuit, enabling compatibility with both AC and DC power sources.

సరైన పనితీరు మరియు దీర్ఘాయువును నిర్ధారించడానికి ఉత్పత్తిని ఉపయోగించే ముందు దయచేసి ఈ మాన్యువల్‌ను పూర్తిగా చదవండి.

భద్రతా సమాచారం

• ఎల్లప్పుడూ విద్యుత్ సరఫరా వాల్యూమ్ ఉండేలా చూసుకోండిtage and polarity are correct before connecting to the board. Incorrect voltage or polarity can damage the device.
• Avoid touching electronic components while the board is powered to prevent electric shock or damage to sensitive parts.
• Do not expose the board to moisture, extreme temperatures, or static electricity.
• భాగాలు లేదా టంకము జాయింట్లకు భౌతిక నష్టం జరగకుండా బోర్డును జాగ్రత్తగా నిర్వహించండి.
• If you are unsure about any installation or operation step, consult a qualified technician.

ప్యాకేజీ విషయాలు

మీ ప్యాకేజీలో అన్ని అంశాలు ఉన్నాయని ధృవీకరించండి:

• 1 x Dual NE5532 Preampజీవితకర్త బోర్డు
• 2 x Signal Lines

Image: The Dual NE5532 Preamplifier Board shown with the two included signal lines.

సెటప్

1. విద్యుత్ సరఫరా కనెక్షన్

ముందుamplifier board supports a wide range of power inputs:

• AC వాల్యూమ్tage: 5V నుండి 16V
• DC సంtage: 6V నుండి 24V

Connect your power source to the designated power input terminals on the board. Ensure correct polarity for DC power. The board is designed with a rectifier circuit and filter capacitors for stable operation with both AC and DC inputs.

చిత్రం: పైగాview ముందు యొక్కamplifier board, highlighting power input (blue terminal block on the left) and audio connections.

2. Audio Input and Output Connections

Connect your audio source (e.g., microphone, audio player) to the "IN" terminals (L, GND, R) and your audio output device (e.g., amplifier, speakers) to the "OUT" terminals (L, GND, R). Use the provided signal lines or appropriate audio cables.

3. Magnification Adjustment (Optional)

The board features R1 and R5 as magnification setting resistors. The default magnification is approximately 5 times. You can adjust the magnification by changing these resistors.

• ప్రతిఘటన పరిధి: 5kΩ to 100kΩ.
• A larger resistance value will result in higher magnification.
• If using plug-in resistors, carefully remove the original surface-mount chip resistors by soldering and then solder the new plug-in resistors onto the pads at both ends of the patch position.

చిత్రం: వివరణాత్మకం view of the board. R1 and R5 resistors are located near the NE5532 operational amplifier chips, allowing for magnification adjustment.

ఆపరేటింగ్ సూచనలు

1. పవర్ ఆన్

Once all connections (power, audio input, audio output) are securely made, apply power to the board. An LED indicator (if present) should illuminate, indicating the board is powered.

2. వాల్యూమ్ నియంత్రణ

Adjust the potentiometer (rotary knob) on the board to control the output volume. Start with the volume at a low setting and gradually increase it to your desired level to avoid sudden loud sounds.

3. ఆడియో ప్లేబ్యాక్

Begin playing audio from your connected source. The preamplifier will boost the signal before sending it to your output device.

నిర్వహణ

• Keep the board clean and free from dust. Use a soft, dry brush or compressed air for cleaning.
• అన్ని కనెక్షన్లు సురక్షితంగా ఉన్నాయని నిర్ధారించుకోవడానికి కాలానుగుణంగా వాటిని తనిఖీ చేయండి.
• Store the board in a dry, cool environment when not in use.
• The NE5532 operational amplifier chips are socketed, allowing for easy replacement or upgrade with other pin-compatible ICs if desired.

ట్రబుల్షూటింగ్

• ధ్వని లేదు:
  • Check all power and audio connections. Ensure they are firmly seated and correctly wired.
  • విద్యుత్ సరఫరా సరైన వాల్యూమ్‌ను అందిస్తుందో లేదో ధృవీకరించండి.tage (AC 5-16V or DC 6-24V).
  • Ensure the audio source is playing and the output device is powered on and set to the correct input.
  • Adjust the volume potentiometer on the board.
• Hum or Hissing Noise:
  • Check for proper grounding of all audio components.
  • Ensure audio cables are shielded and not running parallel to power cables.
  • Move the unit or cabling away from potential sources of electromagnetic interference (RFI), such as power transformers, motors, or wireless devices.
  • Verify the power supply is stable and free from ripple.
• వక్రీకరించిన ధ్వని:
  • Reduce the input signal level if it is too high.
  • Check the magnification setting (R1, R5 resistors); if it's too high for your application, consider reducing it.
  • Ensure the output device (e.g., amplifier) is not overdriven.

స్పెసిఫికేషన్లు

వారంటీ మరియు మద్దతు

For warranty information and technical support, please refer to the seller's policies or contact GODIYMODULES directly through their official channels. Keep your purchase receipt as proof of purchase.