1. పరిచయం
The T238 1.9 Digital Trigger Unit (DTU) is an advanced programmable MOSFET module designed to enhance the performance of AIRSOFT and Gel Ball Blaster V2 Gearboxes. It integrates a high-speed processor and two high-power MOSFET chips to provide a range of features including binary trigger, automatic magazine loading, overheating protection, and gearbox stall protection. This unit significantly improves the stability, shooting speed, and response time of your gearbox, while also contributing to increased battery durability and preventing gear over-rotation.
2. భద్రతా సమాచారం
- This product requires soldering and wiring. Incorrect installation can damage the unit or the connected device.
- It is highly recommended that installation and any modifications be undertaken by an experienced technician.
- Ensure the power source is disconnected before attempting any installation or maintenance.
- ఆపరేటింగ్ వాల్యూమ్tage must be within 7.4-11.1V. Using voltages outside this range may cause damage.
- Always handle electronic components with care to avoid electrostatic discharge.
3. సెటప్ మరియు ఇన్స్టాలేషన్
The T238 1.9 DTU is compatible with various standard V2 Gearboxes. Installation involves soldering and careful wiring within the gearbox.
3.1 భాగాలు పూర్తయ్యాయిview
3.2 Wiring and Soldering
The DTU comes with pre-attached wiring. However, integration into your gearbox will require soldering connections to the motor and battery terminals. Ensure all connections are secure and properly insulated to prevent short circuits. The wiring uses aviation-grade Teflon lines, which are resistant to folding, wear, high temperatures, and offer low impedance.
For detailed wiring diagrams and installation instructions, please refer to the official PDF manual available at: T238 Digital Trigger Unit V2-1.9 PDF Manual.
4. ఆపరేటింగ్ సూచనలు
Once installed, the T238 DTU offers several programmable functions to enhance your experience.
4.1 Binary Trigger Mode
To activate the binary trigger mode:
- Set the selector switch to the semi-auto position.
- ట్రిగ్గర్ని 3 సెకన్ల పాటు లాగి పట్టుకోండి.
This will switch the semi-auto function into binary trigger shooting mode, allowing one shot on trigger pull and another on trigger release.
4.2 Automatic Pre-supply Function
This function is designed for gel ball blaster magazines equipped with an internal motor. When you change the magazine, the magazine motor will automatically run for 0.5 seconds to pre-supply gel balls into the tee. This ensures consistent feeding.
4.3 Active Braking
The active braking feature uses the motor's inertia to stop the piston without delay. This is particularly effective with high-torque motors. It also prevents gear over-rotation, ensuring that single shots remain single shots even under high voltage, and allows the spring to fully release in semi-auto mode, reducing strain on gearbox components and extending their lifespan.
5. నిర్వహణ
To ensure the longevity and optimal performance of your T238 DTU, follow these maintenance guidelines:
- జనరల్ క్లీనింగ్: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
- Terminal Care: The motor plug adopts imported silver-plated terminals to prevent oxidation and suppress current flow issues. Avoid bending or damaging these terminals.
- వైరింగ్ తనిఖీ: Periodically check all wiring for signs of wear, fraying, or loose connections. Repair or replace damaged wiring promptly.
- నిల్వ: Store the DTU in a dry, cool environment away from direct sunlight and extreme temperatures.
6. ట్రబుల్షూటింగ్
This section provides solutions to common issues you might encounter with your T238 DTU.
6.1 Gearbox Block-up Protection
- లక్షణం: The system stops working and emits an elongated 'beep' sound.
- కారణం: The gearbox has stalled (e.g., due to a jam or mechanical issue).
- పరిష్కారం: Immediately power off the device. Check the gearbox for any obstructions or mechanical failures. Resolve the issue before powering on again.
6.2 DTU Overheat Protection
- లక్షణం: After pulling the trigger, the motor gives a beep prompt, and the unit may not function.
- కారణం: The DTU has overheated.
- పరిష్కారం: Allow the unit to cool down. The system will automatically restart after cooling. Avoid continuous rapid firing that might lead to overheating.
7. స్పెసిఫికేషన్లు
| ఫీచర్ | వివరాలు |
|---|---|
| మోడల్ సంఖ్య | T238 1.9 v2 |
| పరిమాణం | 49 x 28 x 15 మిమీ |
| ఆపరేటింగ్ వాల్యూమ్tage | 7.4 - 11.1 వి |
| గరిష్ట ఇన్రష్ కరెంట్ | 300A |
| Maximum Brake Current | 100A |
| అనుకూలత | Standard Gearbox V2 |
| మెటీరియల్ | ప్లాస్టిక్ |
| సర్టిఫికేషన్ | CE |
| సిఫార్సు చేసిన వయస్సు | 14+ సంవత్సరాలు |
8 వినియోగదారు చిట్కాలు
- వృత్తిపరమైన సంస్థాపన: Due to the soldering and wiring requirements, it is strongly advised to have this unit installed by a qualified technician to prevent damage and ensure proper function.
- Wiring Included: The product comes with the necessary wiring for installation.
- Silver-Plated Terminals: The unit features silver-plated terminals on the motor plug, which helps prevent oxidation and ensures stable current flow, contributing to better performance and longevity.
9. వారంటీ మరియు మద్దతు
This product includes a warranty. For any questions or issues regarding the T238 1.9 Digital Trigger Unit, please contact customer service. It is important to reach out to customer service first if you encounter any problems after receiving the goods.
