MACHINIST H61 మదర్‌బోర్డ్ యూజర్ మాన్యువల్

1. పరిచయం

This manual provides detailed instructions for the installation, operation, and troubleshooting of your MACHINIST H61C Motherboard. Please read this manual thoroughly before proceeding with installation to ensure proper setup and to prevent damage to your components.

For a complete PDF version of this manual, please refer to the official document: MACHINIST H61C User Manual (PDF)

Figure 1.1: MACHINIST H61C Motherboard and packaging

2. ప్యాకేజీ విషయాలు

మీ ప్యాకేజీలో అన్ని అంశాలు ఉన్నాయని ధృవీకరించండి:

• 1 x MACHINIST H61C Motherboard
• 1 x I/O షీల్డ్
• 1 x SATA కేబుల్

Note: Gift accessories are manually tested before packaging. Please understand if any are missing.

3. సెటప్ మరియు ఇన్‌స్టాలేషన్

3.1. CPU and CPU Fan Installation

Follow these steps to install the CPU into the LGA 1155 socket:

1. Press down on the lever and lift it.
2. Open the CPU cover.
3. Align the triangle symbols of the socket and the CPU, then gently place the CPU into the socket.
4. Remove the CPU plastic cover.
5. Align the groove with the screw hole and lower the lever to secure the CPU.

Figure 3.1: CPU Installation Steps

ముఖ్యమైన పరిగణనలు:

• Ensure the motherboard supports your specific CPU model.
• హార్డ్‌వేర్ డ్యామేజ్‌ని నివారించడానికి CPUని ఇన్‌స్టాల్ చేయడానికి లేదా తీసివేయడానికి ముందు పవర్ అవుట్‌లెట్ నుండి పవర్ కార్డ్‌ను ఎల్లప్పుడూ అన్‌ప్లగ్ చేయండి.
• Retain the CPU protective cap after installation.
• Do not power on the computer if the CPU cooler is not installed; this can cause overheating and damage.
• Confirm the CPU heat sink forms a tight seal with the CPU before booting.
• Apply an even layer of thermal paste between the CPU and heatsink for optimal heat dissipation.
• Protect CPU socket pins with a plastic cap when no CPU is installed.
• Do not force the CPU into the socket before the locking lever is lifted.
• 4-పిన్ CPU ఫ్యాన్ పవర్ కనెక్టర్‌ను మదర్‌బోర్డ్‌లోని 4-పిన్ CPU ఫ్యాన్ హెడర్‌కు కనెక్ట్ చేయండి.
• Ensure the 4-PIN power supply is plugged in to power the CPU.

Figure 3.2: CPU Pin Condition (Abnormal vs. Normal)

3.2. మెమరీ సంస్థాపన

The motherboard features two DDR3 DIMM slots, supporting a maximum capacity of 32GB (16GB per slot).

1. మెమొరీ స్లాట్‌కు రెండు వైపులా ఉన్న లాచెస్‌ను బయటికి తిప్పండి.
2. Insert the memory module into the slot, aligning it with the notch.
3. మెమరీని లాక్ చేయడానికి స్లాట్‌కు రెండు వైపులా లాచ్‌లను తిప్పండి.

ముఖ్యమైన పరిగణనలు:

• Use DDR3 desktop memory.
• For optimal performance, use memory modules of the same capacity, brand, speed, and chips.
• Always turn off the computer and unplug the power cord before installing memory.
• Memory modules have a foolproof design; if it doesn't fit, try reversing it.
• Dual-Channel mode requires two memory modules to be installed.

3.3. విస్తరణ కార్డ్ సంస్థాపన

The motherboard provides one PCI Express 2.0 x16 slot and one PCI Express 2.0 x1 slot.

• Place the expansion card into an available PCI Express slot.
• Press the card firmly until it is fully inserted and secured.

ముఖ్యమైన పరిగణనలు:

• Always turn off the power supply and unplug the power cable before adding or removing expansion cards.
• Incorrect installation can cause short circuits, potentially damaging the card or motherboard.

Figure 3.3: DDR3 and PCIe Expansion Slots

3.4. అంతర్గత కనెక్టర్లు

Connect your case's front panel headers, audio, and USB ports to the corresponding connectors on the motherboard.

F_PANEL1 Connector (Front Panel Header)

This header is for connecting the power LED, power switch, HDD LED, and reset switch from your computer case.

+POWER LED-  +POWER SW-  +HDD LED-  +RESET SW-

SPEAK1 Connector (Speaker Header)

Connect your case's internal speaker here.

+ Buzzer + Speaker

F_AUDIO1 Connector (Front Audio Header)

This connector allows you to connect audio jacks on the front panel of your case.

Important: An incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

USB Connectors (F_USB1, FP_USB3_1)

These headers allow you to connect USB 2.0 ports on the front panel of your case.

3.5. Storage Ports

The motherboard provides three SATA 2.0 (3Gb/s) connectors (SATA1-SATA3) and one M.2 slot.

• SATA పోర్ట్‌లు: ప్రతి SATA కనెక్టర్ ఒకే SATA పరికరానికి మద్దతు ఇస్తుంది.
• M.2 స్లాట్: Insert your M.2 SSD into the M.2 slot at a 30-degree angle and secure it with a screw. The M.2 slot supports both NVME and NGFF protocols. Refer to the product listing for details on switching between SATA M.2 and NVME M.2 modes.

Figure 3.4: M.2 SSD Installation and Protocol Switching

3.6. Power Connectors (ATXPWR)

Ensure your power supply is turned off and all devices are properly installed before connecting power.

• 24-PIN ATXPWR1: For motherboard power supply.
• 4-PIN ATX12V1: For CPU power supply.

Important: A power supply of at least 500W is recommended. Insufficient power can lead to an unstable or unbootable system.

3.7. Fan Connectors

• CPU_FAN1 (4-pin): For the CPU cooler. Note that this 4-pin connector does not support PWM speed regulation, meaning it cannot intelligently control fan speed based on load or temperature.
• SYS_FAN1 (3-pin): For system chassis fans. This 3-pin connector also does not have a PWM setting option.

4. Operating the BIOS

4.1. BIOS Overview

The BIOS (Basic Input and Output System) stores hardware parameters in the CMOS on the motherboard. It identifies, configures, tests, and connects computer hardware to the OS upon startup. Key functions include Power-On Self-Test (POST), saving system parameters, and loading the operating system. The BIOS Setup program allows users to modify basic system configuration settings and activate certain features.

Important: BIOS flashing is potentially risky. It is recommended not to flash the BIOS unless you encounter problems with the current version. Inadequate flashing can lead to system malfunction. We are not responsible for issues caused by unauthorized BIOS flashing.

4.2. Entering BIOS Setup

When the computer powers on, the BIOS performs a self-test. After the self-test, you will see a message prompting you to press the "DEL" key to enter the BIOS Setup Menu, or "F11" for the Quick Boot Key.

• If the message disappears too quickly, you can turn off and then turn on your computer, press the Reset button on the case, or press Ctrl+Alt+Delete to restart and try again.

Important: BIOS functions may vary depending on the product version. If you encounter any issues, please contact technical support.

4.3. Resetting BIOS

To restore default BIOS settings, which can help resolve certain issues, short the Clear CMOS jumper on the motherboard.

Important: Always turn off the computer before clearing CMOS data.

Figure 4.1: Clear CMOS Jumper (JCMOS1)

Clear CMOS Steps:

1. ప్రారంభ స్థితి: The jumper covers pins "1" and "2".
2. డిశ్చార్జ్: Pull out the cap and place it to cover pins "2" and "3". Wait for approximately 3 minutes for the discharge to complete.
3. Restitute: After discharge, restore the jumper to its initial state (covering pins "1" and "2").

5. నిర్వహణ

To ensure the longevity and optimal performance of your motherboard, consider the following maintenance tips:

• శుభ్రముగా ఉంచు: Regularly clean dust from inside your computer case, especially around the motherboard, CPU cooler, and fan vents, using compressed air.
• సరైన గాలి ప్రవాహాన్ని నిర్ధారించుకోండి: Make sure your case has adequate ventilation and that fans are functioning correctly to prevent overheating.
• కనెక్షన్‌లను తనిఖీ చేయండి: Periodically inspect all cables and connectors (power, data, expansion cards) to ensure they are securely seated.
• థర్మల్ పేస్ట్: If you replace your CPU or CPU cooler, reapply thermal paste to ensure efficient heat transfer.
• విద్యుత్ సరఫరా: Use a reliable power supply unit (PSU) with sufficient wattage (at least 500W recommended) to provide stable power to all components.

6. ట్రబుల్షూటింగ్ (తరచుగా అడిగే ప్రశ్నలు)

If you encounter problems, refer to these common issues and solutions:

6.1. Computer Can't Boot (No response, no fan rotation, no indicator light)

1. Clear the CMOS jumper (refer to Section 4.3).
2. CPU మదర్‌బోర్డుకు అనుకూలంగా ఉందో లేదో తనిఖీ చేయండి.
3. Verify that the motherboard's power and CPU power supply cables are properly plugged in, and the case power switch is on.
4. Ensure the system panel power-on cable is plugged in correctly.
5. Check if your power supply unit (PSU) is in good working condition.
6. Remove the graphics card, hard disk, USB devices, and other peripherals, then attempt to boot. You can short the switch pins directly with a metal object to rule out case switch issues.
7. Try replacing the CPU with another compatible one.

6.2. Computer Starts Up and Then Immediately Shuts Down

1. Clear the CMOS jumper (refer to Section 4.3).
2. Check if the CPU model used is compatible.
3. Replace and troubleshoot if the CPU is damaged.
4. మెమరీ మాడ్యూళ్లను భర్తీ చేయండి.
5. Remove the graphics card, hard drive, and USB devices, then test again.

6.3. Computer Keeps Restarting (Reboot Loop)

1. Clear the CMOS jumper (refer to Section 4.3).
2. CPU మదర్‌బోర్డుకు అనుకూలంగా ఉందో లేదో తనిఖీ చేయండి.
3. Check if the CPU is defective (try replacing with a new one).
4. Replace the RAM and check for compatibility or defects.
5. Remove the graphics card, hard disk, USB devices, and other peripherals, then test again.

6.4. No Display (Monitor shows no signal)

State 1: Fan rotating, Caps Lock key does not respond.

1. Clear CMOS (refer to Section 4.3).
2. Check if the motherboard's power supply and the CPU power supply are plugged in.
3. Check if the memory stick is installed in the correct slot. Some motherboards are sensitive to memory slot placement.
4. Check if the CPU and memory models are compatible with the motherboard.
5. CPUని భర్తీ చేయండి.
6. మెమరీని భర్తీ చేయండి.

State 2: Fan rotating, Caps Lock key lights up.

1. Check if the monitor is turned on.
2. Check if the monitor display cable (HDMI, VGA) is plugged in correctly.
3. If using a CPU without integrated graphics (e.g., Intel Xeon series or 'F' suffix Intel Core CPUs), a dedicated graphics card must be installed.
4. Ensure the display data cable is connected to the correct display interface (motherboard's integrated graphics port if no discrete GPU, or discrete GPU's port if installed).
5. Replace the data cable connected to the monitor.
6. గ్రాఫిక్స్ కార్డ్‌ను భర్తీ చేయండి.

6.5. Blue Screen or System Crash

1. Check if the motherboard's heat dissipation is normal (e.g., CPU fan working, cooler tightly fitted, thermal paste applied).
2. CPUని భర్తీ చేయండి.
3. మెమరీని భర్తీ చేయండి.
4. హార్డ్ డిస్క్‌ను భర్తీ చేయండి.
5. Reinstall the operating system.
6. విద్యుత్ సరఫరాను భర్తీ చేయండి.

7. స్పెసిఫికేషన్లు

Figure 7.1: Motherboard Physical Dimensions

Figure 7.2: Motherboard Interface Distribution Schematic

Figure 7.3: Back I/O Ports

చిత్రం 7.4: కీలక లక్షణాలు ముగిసిందిview

చిత్రం 7.5: అదనపు లక్షణాలు

8 వినియోగదారు చిట్కాలు

• CPU Fan Control: The motherboard's CPU_FAN1 connector does not support PWM speed regulation. If you require fine-grained fan speed control, consider using an external fan controller.
• CPU అనుకూలత: This motherboard supports Intel LGA 1155 processors, including Intel Core i7 3770 and Xeon E3 1220 v2. It is NOT compatible with processors like the Xeon E5 2680v4 (which uses a different socket, LGA 2011-3). Always verify your CPU's socket type and generation.
• RAM Selection: For best compatibility and stability, use DDR3 desktop memory from international brands such as Samsung, Kingston, Sandee, Micron, and Hynix. Ensure the RAM is non-ECC (Error-Correcting Code) as ECC RAM is typically for server motherboards.
• విద్యుత్ సరఫరా: A robust power supply of at least 500W from a reputable brand is highly recommended to ensure stable operation, especially when using a dedicated graphics card or multiple peripherals.
• డ్రైవర్లు: If you experience issues with specific components or features, check the manufacturer's website for the latest drivers for the H61 chipset.
• TPM 2.0: This motherboard, based on the H61 chipset, typically does not support TPM 2.0, which is a requirement for Windows 11. If TPM 2.0 is essential for your use case, this motherboard may not be suitable.

9. మద్దతు

If you encounter any problems while using the product that are not covered in this manual or the troubleshooting section, please contact your technical support provider for assistance. Provide your product model and a detailed description of the issue for faster resolution.