ఉత్పత్తి ముగిసిందిview
The DIG PRV075 is a pipe thread adjustable pressure regulator designed to reduce and regulate incoming water pressure for drip irrigation and micro-sprinkler systems. It ensures the system operates within the appropriate pressure range, typically between 28 PSI and 60 PSI, providing consistent outlet pressure regardless of upstream fluctuations.
చిత్రం: ముందు భాగం view of the DIG PRV075 Adjustable Drip Pressure Regulator, showing its black plastic body and red adjustment cap.
ముఖ్య లక్షణాలు:
- Adjustable pressure range with a single screw for fine-tuning.
- Rolling diaphragm design prevents debris from entering the spring assembly, ensuring longevity.
- Maintains reliable control of outlet pressure despite variations in incoming pressure or flow.
- Equipped with 3/4" female pipe thread (FPT) inlet and outlet for compatibility with standard connections.
సెటప్ మరియు ఇన్స్టాలేషన్
Proper installation is crucial for the optimal performance of your DIG PRV075 pressure regulator. Follow these steps carefully:
- కనెక్షన్ పాయింట్లను గుర్తించండి: The PRV075 has 3/4" female pipe threads on both the inlet and outlet. Ensure your irrigation system components have compatible male pipe threads.
- Prepare the Connection: Turn off the main water supply to the irrigation line where the regulator will be installed.
- Thread the Regulator:
- Apply thread sealant tape (Teflon tape) or pipe dope to the male threads of your water source connection.
- Carefully thread the inlet side of the PRV075 onto the prepared male thread. Hand-tighten first, then use a wrench for an additional 1 to 2 turns until snug. Do not overtighten.
- Repeat the process for the outlet side, connecting it to your drip irrigation or micro-sprinkler system.
- లీక్ల కోసం తనిఖీ చేయండి: Slowly turn on the main water supply and inspect all connections for leaks. Tighten any leaking connections gently.
చిత్రం: వైపు view of the DIG PRV075 Pressure Regulator held in a hand, illustrating its compact size and showing approximate dimensions of 5.1 inches (12 cm) in length.
ఆపరేటింగ్ సూచనలు
The DIG PRV075 is designed for easy pressure adjustment. Follow these steps to set the desired operating pressure:
- సర్దుబాటు స్క్రూను గుర్తించండి: The pressure adjustment screw is located under the red cap at one end of the regulator. Gently pry off the red cap to expose the screw.
- ఒత్తిడిని సర్దుబాటు చేయండి:
- Use a flathead screwdriver to turn the adjustment screw.
- Turning the screw సవ్యదిశలో రెడీ పెరుగుతుంది the outlet pressure.
- Turning the screw అపసవ్య దిశలో రెడీ తగ్గుదల the outlet pressure.
- Make small adjustments and observe the system's performance. For precise adjustment, use a pressure gauge downstream of the regulator.
- ఆపరేటింగ్ రేంజ్: The regulator is designed to operate within a range of 28 PSI to 60 PSI. Do not attempt to adjust outside this range.
- క్యాప్ను భర్తీ చేయండి: Once the desired pressure is set, securely replace the red protective cap.
నిర్వహణ
The DIG PRV075 is designed for minimal maintenance. However, periodic checks can ensure its long-term performance:
- లీక్ల కోసం తనిఖీ చేయండి: Periodically check all connections for any signs of water leaks. Address any leaks promptly by tightening connections or replacing thread sealant.
- శిధిలాల కోసం తనిఖీ చేయండి: While the rolling diaphragm helps prevent debris, if you notice inconsistent pressure or reduced flow, it may indicate debris accumulation. Turn off the water, disconnect the regulator, and inspect the inlet and outlet for any blockages. Clean gently with water if necessary.
- శీతాకాలం: In regions subject to freezing temperatures, it is recommended to drain the irrigation system, including the pressure regulator, to prevent damage from freezing water.
ట్రబుల్షూటింగ్
| సమస్య | సాధ్యమైన కారణం | పరిష్కారం |
|---|---|---|
| No water flow or very low flow |
|
|
| Pressure too high or too low (and cannot be adjusted) |
|
|
| కనెక్షన్ల నుండి నీరు లీక్ అవుతోంది |
|
|
స్పెసిఫికేషన్లు
- మోడల్: PRV075
- బ్రాండ్: డిఐజి
- మెటీరియల్: Plastic body, Stainless Steel exterior finish (referring to internal spring/components)
- ఇన్లెట్/అవుట్లెట్ కనెక్షన్: 3/4" Female Pipe Thread (FPT)
- సర్దుబాటు చేయగల ఒత్తిడి పరిధి: 28 PSI నుండి 60 PSI
- కొలతలు (L x W x H): సుమారు 4 x 2 x 3 అంగుళాలు
- వస్తువు బరువు: సుమారు 1.6 ఔన్సులు
- పోర్టుల సంఖ్య: 2
- వాల్వ్ రకం: Globe Valve (as per specification, though it's a regulator)
- UPC: 013158333333
వారంటీ మరియు మద్దతు
For information regarding product warranty, technical support, or replacement parts, please contact DIG customer service directly. Refer to the official DIG webఅత్యంత తాజా సంప్రదింపు వివరాలు మరియు వారంటీ నిబంధనల కోసం సైట్ లేదా ఉత్పత్తి ప్యాకేజింగ్.
You can visit the official DIG store for more information: DIG Official Store
