1. పరిచయం
This user manual provides essential information for the safe and effective use of the Macurco CM-6-CH Carbon Monoxide (CO) Calibration Hood, designed for use with Macurco CM-6 and CM-12 fixed gas detectors. Please read this manual thoroughly before installation, operation, or maintenance to ensure proper functionality and safety.
2. భద్రతా సమాచారం
ముఖ్యమైనది: Before use, read and follow the user instructions inside the box. Failure to do so may result in improper operation, inaccurate readings, or personal injury.
- Always ensure the calibration hood is used in a well-ventilated area.
- Do not paint the device, as this may interfere with its operation or sensor accuracy.
- Handle with care to avoid damage to the hood or the detector.
- Refer to the specific instructions for your Macurco CM-6 or CM-12 detector for detailed calibration procedures.
3. ఉత్పత్తి ముగిసిందిview
The Macurco CM-6-CH is a specialized calibration hood designed to facilitate the accurate calibration of Macurco CM-6 and CM-12 Carbon Monoxide fixed gas detectors. It ensures a controlled environment for applying calibration gas to the sensor, optimizing the detector's performance and accuracy.
మూర్తి 3.1: ముందు view of the Macurco CM-6-CH product packaging, showing the product name, brand, and key specifications for the CM-12 detector.
మూర్తి 3.2: వివరంగా view of the Macurco CM-12 detector diagram and technical specifications printed on the product box, including power, range, color, temperature, and certifications.
4. సెటప్
The CM-6-CH calibration hood is designed for easy attachment to compatible Macurco CO detectors. Follow these general steps for setup:
- Ensure your Macurco CM-6 or CM-12 detector is properly installed and powered.
- Carefully align the CM-6-CH calibration hood with the sensor area of the detector.
- Securely attach the hood to create a sealed environment around the sensor. Refer to your detector's manual for specific attachment points or methods.
- Connect the calibration gas cylinder to the inlet port on the calibration hood.
5. Operating the Calibration Hood
The calibration hood facilitates the application of a known concentration of CO gas to the detector's sensor for accurate calibration. Always follow the calibration procedure outlined in your Macurco CM-6 or CM-12 detector's specific user manual.
General Calibration Steps:
- With the calibration hood securely attached and the calibration gas connected, initiate the calibration sequence on your Macurco detector.
- Open the valve on the calibration gas cylinder to allow the gas to flow into the hood and over the sensor.
- Monitor the detector's display and indicators as per its manual until the calibration process is complete.
- Once calibration is confirmed, close the gas cylinder valve and remove the calibration hood.
The detector is designed to operate within a temperature range of 0 to 35°C (32 to 95°F) and a CO detection range of 0-200 PPM. Ensure your calibration environment adheres to these specifications for optimal results.
6. నిర్వహణ
The CM-6-CH calibration hood requires minimal maintenance. Keep it clean and free from obstructions to ensure proper sealing during calibration.
- ఒక మృదువైన, d తో బాహ్య తుడవడంamp వస్త్రం. కఠినమైన రసాయనాలు లేదా రాపిడి క్లీనర్లను ఉపయోగించవద్దు.
- Ensure the internal surfaces that contact the detector are clean and free of debris.
- Store the calibration hood in a clean, dry place when not in use to prevent damage.
- As indicated on the product, do not paint పరికరం.
7. ట్రబుల్షూటింగ్
If you encounter issues during calibration, consider the following:
- అమరిక వైఫల్యం: Ensure the calibration hood is securely attached and creating a proper seal. Verify the calibration gas cylinder is not empty and the flow rate is correct.
- సరికాని రీడింగ్లు: Check the expiration date of your calibration gas. Ensure the ambient temperature is within the specified operating range for the detector.
- భౌతిక నష్టం: Inspect the calibration hood for any cracks or deformities that might prevent a proper seal. Replace if damaged.
For persistent issues, refer to the troubleshooting section of your Macurco CM-6 or CM-12 detector manual or contact Macurco technical support.
8. స్పెసిఫికేషన్లు
| ఫీచర్ | స్పెసిఫికేషన్ |
|---|---|
| మోడల్ సంఖ్య | CM-6-CH (for CM-6 / CM-12 detectors) |
| బ్రాండ్ | Macurco |
| వస్తువు బరువు | 0.96 ఔన్సులు (27.22 గ్రా) |
| UPC | 808237728892 |
| Power (CM-12 Detector) | 100-240 VAC (50 to 60 Hz) |
| CO Range (CM-12 Detector) | 0-200 పిపిఎం |
| Operating Temperature (CM-12 Detector) | 0 నుండి 35°C (32 నుండి 95°F) |
| Certifications (CM-12 Detector) | UL 2075, UL 61010-1, CSA C22.2 No 61010-1 |
మూర్తి 8.1: టాప్ view of the Macurco CM-6-CH product packaging, displaying the UPC barcode (0783748811304) and "Made in the USA" label.
9. వారంటీ మరియు మద్దతు
For warranty information and technical support regarding your Macurco CM-6-CH calibration hood or compatible detectors, please contact the manufacturer:
తయారీదారు: Macurco (Manufactured by Aerionics Inc.)
ఫోన్: 1-877-367-7891
Webసైట్: www.macurco.com
Please have your product model number (CM 6) and any relevant purchase information ready when contacting support.
