పరిచయం
The DAP Presto Patch is designed for simple, structural, and invisible repair of holes in drywall. This patch is suitable for repairing holes up to 6-7/8 inches (17.5 cm) in diameter. It restores structural integrity and provides a permanent, time-saving solution for wall repair.
ఉత్పత్తి లక్షణాలు
- Restores structural integrity of damaged drywall.
- Made with real drywall material.
- Designed to make repairs invisible when properly finished.
- Time-saving solution for quick repairs.
- Porous drywall paper for permanent repair.
- Repairs standard 1/2 inch drywall.
- Pre-cut for easy installation.
చేర్చబడిన భాగాలు
- One (1) Pre-cut drywall patch with oversized taping paper attached.
- One (1) Foam template (for guiding hole cutting).
స్పెసిఫికేషన్లు
| గుణం | వివరాలు |
|---|---|
| బ్రాండ్ | DAP |
| మోడల్ సంఖ్య | 9157 |
| Patch Diameter | 6-7/8 అంగుళాలు (17.5 సెం.మీ.) |
| Patch Thickness | 1/2 అంగుళం |
| ఆకారం | గుండ్రంగా |
| మౌంటు రకం | Adhesive (with taping paper) |
| వస్తువు బరువు | 0.6 పౌండ్లు (సుమారుగా) |
| ఆపరేటింగ్ ఉష్ణోగ్రత | 45 - 85 degrees F |
భద్రతా సమాచారం
Always wear appropriate personal protective equipment (PPE) such as safety glasses and gloves when working with drywall and patching compounds. Ensure adequate ventilation in the work area. Keep out of reach of children and pets. Refer to the product packaging for any specific safety warnings or first aid instructions.
సెటప్ మరియు తయారీ
Before applying the DAP Presto Patch, ensure the area around the hole is clean, dry, and free of loose debris. For best results, the ambient temperature should be between 45 and 85 degrees Fahrenheit.
Step 1: Prepare the Hole (PREP)
Use the provided foam template to trace a circle around the damaged area on the wall. Carefully cut out the traced circle using a utility knife or drywall saw, ensuring a clean, round opening. The hole should be slightly smaller than the patch's drywall core to allow the patch's paper flange to adhere to the wall surface.
Figure 1: Preparation step, showing how to cut the hole in the drywall to match the patch. This corresponds to the "PREP" section on the product packaging image.
ఆపరేటింగ్ సూచనలు (అప్లికేషన్)
Step 2: Apply the Patch (PATCH)
Remove the protective backing from the adhesive side of the Presto Patch. Insert the patch into the prepared hole, ensuring the drywall core fits snugly within the opening and the oversized taping paper lies flat against the wall surface. Press firmly around the entire perimeter of the taping paper to ensure good adhesion.
Figure 2: Patch application step, showing the patch being placed over the hole. This corresponds to the "PATCH" section on the product packaging image.
Step 3: Finish the Repair (FINISH)
Apply a thin, even coat of joint compound (not spackle) over the entire patch, feathering the edges smoothly into the surrounding wall. Allow the first coat to dry completely according to the joint compound manufacturer's instructions. Apply additional thin coats as needed, sanding lightly between coats until the patch is completely blended and invisible. Once dry, the area can be primed and painted to match the existing wall.
Figure 3: Finishing step, illustrating the application of joint compound to blend the patch. This corresponds to the "FINISH" section on the product packaging image.
నిర్వహణ
Once the repair is complete and painted, no special maintenance is required for the patch itself. Treat the repaired area as you would any other part of your drywall. Avoid excessive moisture or impact to the repaired area to ensure longevity.
ట్రబుల్షూటింగ్
- Patch Not Adhering: Ensure the wall surface is clean, dry, and free of dust or grease. Apply firm, even pressure across the entire taping paper. Ensure the ambient temperature is within the recommended range (45-85°F).
- Patch Visible After Finishing: This usually indicates insufficient joint compound application or improper feathering/sanding. Apply additional thin coats of joint compound, extending slightly beyond the previous layer, and sand smoothly until the patch is undetectable. Ensure proper lighting when sanding to identify imperfections.
- Cracks Appearing: Cracks can occur if the joint compound is applied too thickly in one coat, or if the wall experiences significant movement. Ensure thin, multiple coats are applied. For structural issues causing wall movement, address the underlying problem before patching.
- Hole Too Large: The Presto Patch is designed for holes 6-7/8 inches and smaller. For larger holes, a different repair method involving cutting and screwing in a new piece of drywall may be necessary.
వారంటీ సమాచారం
Specific warranty details for the DAP Presto Patch are not provided in the product information. For warranty inquiries, please contact DAP customer service directly.
కస్టమర్ మద్దతు
For further assistance or technical support, please visit the official DAP webసైట్లో లేదా వారి కస్టమర్ సర్వీస్ విభాగాన్ని సంప్రదించండి. సంప్రదింపు సమాచారం సాధారణంగా ఉత్పత్తి ప్యాకేజింగ్ లేదా తయారీదారు యొక్క webసైట్.
