పరిచయం
This manual provides essential information for the safe and effective use of the Hakko CHP TR-20-TM Micro Soft Wire Cutter. This precision tool is designed for cutting integrated circuit (IC) pins and soft wires up to 22 AWG (0.6mm).
Figure 1: Hakko CHP TR-20-TM Micro Soft Wire Cutter. This image displays the tool's overall design, highlighting its red and black ergonomic handles and the precise, angled cutting jaws.
ఉత్పత్తి లక్షణాలు
- Reverse-Cut Micro Soft-Wire Cutter: Features an 8mm long jaw with a reverse angle head, specifically designed for flush-cutting IC pins up to 22 gauge (0.6mm).
- Angled Cutting Surface: The 48-degree reverse angled cutting surface facilitates precise cutting of closely-spaced IC pins.
- మన్నికైన నిర్మాణం: Constructed from 2.0mm heat-treated carbon steel for enhanced durability and extended tool life.
- స్మూత్ ఆపరేషన్: Precision-ground holes and surfaces ensure smooth movement of the cutting jaws.
- Reduced Operator Fatigue: An internal spring mechanism automatically returns the tool to the open position after each cut, minimizing hand strain.
- ఎర్గోనామిక్ డిజైన్: Dolphin-style nonslip hand grips provide comfort and control during prolonged use.
- చేతి రక్షణ: A curved fore-edge on the handles protects hands from cutting surfaces.
- తుప్పు నిరోధకత: Parkerized surfaces prevent glare and increase the tool's resistance to corrosion.
సెటప్
The Hakko CHP TR-20-TM Micro Soft Wire Cutter is ready for use out of the packaging. No assembly is required.
- ప్రారంభ తనిఖీ: Before first use, inspect the tool for any signs of damage or manufacturing defects. Ensure the jaws align properly and the spring mechanism operates smoothly.
- పరిశుభ్రత: Ensure the cutting jaws are clean and free of debris before use to maintain optimal cutting performance.
ఆపరేటింగ్ సూచనలు
Follow these instructions for safe and effective operation of the wire cutter.
- మొదటి భద్రత: Always wear appropriate eye protection when using cutting tools to prevent injury from flying debris.
- పట్టు: Hold the cutter firmly with the ergonomic handles. The nonslip grips are designed for comfort and control.
- స్థానం: Position the wire or IC pin to be cut between the jaws. For flush cuts on IC pins, align the reverse-angled jaw as close as possible to the circuit board or component body.
- కట్టింగ్ కెపాసిటీ: Do not attempt to cut wires or materials exceeding the maximum capacity of 22 AWG (0.6mm) for soft wire. Cutting harder or thicker materials can damage the tool's jaws.
- కట్టింగ్ యాక్షన్: Apply steady, firm pressure to the handles to close the jaws and make the cut. The internal spring will reopen the jaws automatically upon release.
- పారవేయడం: Dispose of cut wire pieces responsibly.
నిర్వహణ
Proper maintenance ensures the longevity and performance of your Hakko wire cutter.
- శుభ్రపరచడం: After each use, wipe the jaws and handles with a clean, dry cloth to remove any debris or residue. For stubborn grime, a slightly damp గుడ్డను ఉపయోగించవచ్చు, తరువాత పూర్తిగా ఆరబెట్టవచ్చు.
- సరళత: Periodically apply a small drop of light machine oil to the pivot point to ensure smooth operation and prevent rust. Wipe off any excess oil.
- నిల్వ: Store the tool in a dry environment to prevent corrosion. Keep the jaws closed when not in use to protect the cutting edges.
- పడవేయడం మానుకోండి: Dropping the tool, especially on hard surfaces, can misalign or damage the precision jaws.
ట్రబుల్షూటింగ్
This section addresses common issues you might encounter with your wire cutter.
| సమస్య | సాధ్యమైన కారణం | పరిష్కారం |
|---|---|---|
| Jaws do not close completely or align properly. | Debris caught between jaws or pivot point; tool has been dropped or damaged. | Clean jaws thoroughly. If damage is suspected, discontinue use and consider replacement. |
| Cutting performance is poor or requires excessive force. | Dull or damaged cutting edges; attempting to cut material beyond capacity. | Inspect cutting edges for nicks or wear. Ensure material is within 22 AWG (0.6mm) soft wire limit. Replace if edges are significantly damaged. |
| Handles feel stiff or sticky. | Lack of lubrication at the pivot point; accumulation of dirt. | Clean the pivot area and apply a small amount of light machine oil. |
స్పెసిఫికేషన్లు
| గుణం | వివరాలు |
|---|---|
| మోడల్ సంఖ్య | TR-20-TM |
| దవడ రకం | Reverse-cut, Micro Flush-cut |
| Jaw Length | 8మి.మీ |
| దవడ కోణం | 48-degree reverse angle |
| గరిష్ట కట్టింగ్ కెపాసిటీ | 22 AWG (0.6mm) soft wire / IC pins |
| నిర్మాణ సామగ్రి | 2.0mm Heat-treated Carbon Steel |
| హ్యాండిల్ మెటీరియల్ | Alloy Steel with Nonslip Grips |
| రంగు | ఎరుపు |
| వస్తువు బరువు | 0.1 పౌండ్లు (సుమారు 45 గ్రాములు) |
| తయారీదారు | Quality Hand Tools |
వారంటీ మరియు మద్దతు
For warranty information or technical support regarding your Hakko CHP TR-20-TM Micro Soft Wire Cutter, please contact American Hakko Products directly. American Hakko Products manufactures soldering and desoldering tools and is headquartered in Valencia, CA.
Please refer to the official Hakko webఅత్యంత ప్రస్తుత వారంటీ నిబంధనలు మరియు సంప్రదింపు వివరాల కోసం సైట్ లేదా మీ కొనుగోలు డాక్యుమెంటేషన్.
తయారీదారు: Quality Hand Tools (as listed on product specifications, associated with Hakko brand)
బ్రాండ్: హక్కో
Webసైట్: www.hakko.com
