FIBARO వాల్ ప్లగ్ యూజర్ మాన్యువల్

1. పరిచయం

The FIBARO Wall Plug is a compact, intelligent plug-in module designed to control lighting or other electrical devices via Z-Wave commands. It is engineered to work with any type of load up to a maximum power of 2500W. This device also features energy consumption measurement, providing instant and total consumption values to your Z-Wave controller.

A visual indicator ring on the plug provides an immediate overview of energy consumption: a green ring indicates low consumption, while a red ring signifies very high consumption. Additionally, the FIBARO Wall Plug offers a unique Z-Wave network range test function.

Image 1.1: The FIBARO Wall Plug (Type E) and its retail packaging.

2. భద్రతా సమాచారం

• Ensure the Wall Plug is connected to a properly grounded electrical outlet.
• Do not exceed the maximum load capacity of 2500W.
• పరికరాన్ని విడదీయవద్దు లేదా సవరించవద్దు.
• నీరు మరియు అధిక తేమ ఉన్న వాతావరణాలకు దూరంగా ఉంచండి.
• ఈ పరికరం ఇండోర్ ఉపయోగం కోసం మాత్రమే.
• శుభ్రపరిచే ముందు పరికరాన్ని పవర్ అవుట్‌లెట్ నుండి అన్‌ప్లగ్ చేయండి.

3. సెటప్

3.1. భౌతిక సంస్థాపన

1. Plug the FIBARO Wall Plug into a standard Type E electrical outlet.
2. Connect the appliance you wish to control into the FIBARO Wall Plug.

Image 3.1: The FIBARO Wall Plug supports Type E and Type F outlets.

3.2. Adding to Z-Wave Network (Inclusion)

1. Place the FIBARO Wall Plug within direct range of your Z-Wave controller.
2. Set your Z-Wave controller into inclusion mode (refer to your controller's manual for specific instructions).
3. Press the button on the FIBARO Wall Plug three times quickly. The LED ring will flash blue to indicate inclusion mode.
4. Once successfully added, the LED ring will change to a steady color, indicating its current power consumption.

3.3. Z-Wave Network Range Test

The Wall Plug can test the Z-Wave network coverage. To activate this function:

1. Press and hold the button on the Wall Plug for a few seconds until the LED ring turns light violet.
2. Release the button. The LED will then display a color indicating the current network coverage:
• ఆకుపచ్చ: Excellent range
• పసుపు: మంచి పరిధి
• నారింజ: Moderate range
• ఎరుపు: పేద పరిధి
• మెరుస్తున్న ఎరుపు: కనెక్షన్ లేదు
3. To exit the test mode, press the button briefly.

4. Operating the Wall Plug

4.1. Basic ON/OFF Control

• మాన్యువల్ కంట్రోల్: Press the button on the Wall Plug once to toggle the connected appliance ON or OFF.
• రిమోట్ కంట్రోల్: Use your Z-Wave controller or associated mobile application to remotely switch the connected appliance ON or OFF.

చిత్రం 4.1: ఉదాample of the FIBARO mobile application interface for controlling devices.

4.2. ఎనర్జీ మానిటరింగ్

The FIBARO Wall Plug continuously monitors the energy consumption of the connected device. The LED ring changes color to visually represent the current power draw:

• ఆకుపచ్చ: తక్కువ విద్యుత్ వినియోగం
• నీలం: Moderate power consumption
• పసుపు: Higher power consumption
• ఎరుపు: Very high power consumption
• మెరుస్తున్న ఎరుపు: Overload warning (disconnect appliance immediately if this occurs).

Detailed energy consumption data (instantaneous power and total accumulated energy) can be viewed through your Z-Wave controller's interface or associated applications.

5. నిర్వహణ

• శుభ్రపరచడం: Use a soft, dry cloth to clean the surface of the Wall Plug. Do not use abrasive cleaners or solvents.
• ఫర్మ్‌వేర్ నవీకరణలు: The FIBARO Wall Plug supports wireless firmware updates when used with a FIBARO Home Center 2 or newer controller. Refer to your controller's manual for instructions on performing firmware updates.

6. ట్రబుల్షూటింగ్

6.1. సాధారణ సమస్యలు

• పరికరం స్పందించడం లేదు:
  • Ensure the Wall Plug is properly plugged into a live outlet.
  • Check the Z-Wave network range using the built-in test function (Section 3.3).
  • Verify that the Wall Plug is correctly included in your Z-Wave network. If not, try re-including it.
• Incorrect energy readings:
  • Ensure the connected appliance is within the specified power limits.
  • Check for any firmware updates for the Wall Plug or your Z-Wave controller.
• LED ring not illuminating:
  • Verify power supply to the outlet.
  • If the device is unresponsive, try unplugging it for 30 seconds and plugging it back in.

6.2. Exclusion from Z-Wave Network

If you need to remove the Wall Plug from your Z-Wave network:

1. Place the FIBARO Wall Plug within direct range of your Z-Wave controller.
2. Set your Z-Wave controller into exclusion mode (refer to your controller's manual).
3. Press the button on the FIBARO Wall Plug three times quickly. The LED ring will flash blue to indicate exclusion mode.
4. Once successfully excluded, the LED ring will stop flashing and the device will no longer be controlled by the network.

7. స్పెసిఫికేషన్లు

8. వారంటీ సమాచారం

Specific warranty details for the FIBARO Wall Plug FGWPE-102 ZW5 EU are not provided in this manual. Please refer to the official FIBARO webసమగ్ర వారంటీ నిబంధనలు మరియు షరతుల కోసం మీ సైట్ లేదా కొనుగోలు కేంద్రం.

9. మద్దతు

For further assistance, technical support, or detailed product documentation, please visit the official FIBARO support website or contact their customer service department. Contact information can typically be found on the FIBARO webసైట్ లేదా ఉత్పత్తి ప్యాకేజింగ్.