పరిచయం
This manual provides essential information for the proper installation, operation, and maintenance of the TURCK BIM-PST-AP6X-V1131 Magnetic Field Sensor. Please read this manual thoroughly before using the product to ensure safe and efficient operation.
మూర్తి 1: A yellow rectangular magnetic field sensor with an M8 male connector on one end. The sensor body is labeled with 'TURCK', 'BIM-PST-AP6X-V1131/KLP80', and power specifications '10...30 VDC 200 mA'. This image shows the overall appearance of the TURCK BIM-PST-AP6X-V1131 sensor.
భద్రతా సూచనలు
Always adhere to local and national safety regulations. Disconnect power before installation or maintenance. Do not exceed specified voltage and current ratings. Only qualified personnel should install and service this device.
- విద్యుత్ ప్రమాదాలను నివారించడానికి సరైన గ్రౌండింగ్ ఉండేలా చూసుకోండి.
- Avoid exposing the sensor to extreme temperatures or corrosive environments beyond its specified operating range.
- Do not modify the sensor in any way, as this may void the warranty and compromise safety.
సెటప్
మౌంటు
The BIM-PST-AP6X-V1131 sensor is designed for cylinder position sensing. It should be mounted securely to the cylinder using the provided KLP-80 mounting bracket. Ensure the active face of the sensor is positioned correctly relative to the magnetic field source (e.g., piston magnet).
- Identify the optimal sensing position on the cylinder.
- Attach the KLP-80 bracket to the cylinder.
- Insert the sensor into the KLP-80 bracket and secure it.
- Adjust the sensor position for precise detection.
వైరింగ్
This is a 3-wire PNP sensor with an M8 male connector. Connect it to a compatible M8 female cable assembly. Refer to the wiring diagram below for standard PNP connections.
| పిన్ చేయండి | Color (Standard) | వివరణ |
|---|---|---|
| 1 | గోధుమ రంగు | +VDC (10-30 VDC) |
| 3 | నీలం | 0 VDC (GND) |
| 4 | నలుపు | Output (PNP Normally Open) |
గమనిక: Always verify pin assignments with the sensor's datasheet or markings if available, as color codes can vary by region or manufacturer.
ఆపరేటింగ్
The TURCK BIM-PST-AP6X-V1131 is an inductive magnetic field sensor designed to detect the presence of a magnetic field, typically from a piston magnet within a pneumatic or hydraulic cylinder. When a magnetic field is detected by the front active face, the PNP output will switch to the supply voltage (+VDC).
కార్యాచరణ
- గుర్తింపు: The sensor detects magnetic fields. Its switching point is factory set.
- అవుట్పుట్: The sensor provides a PNP (Positive-Negative-Positive) output. This means the output switches to a positive voltage when activated.
- సూచిక: Many inductive sensors include an LED indicator that illuminates when the sensor detects a target. Observe the sensor for such an indicator to confirm proper operation.
For optimal performance, ensure the magnetic field strength is consistent and the sensor is not exposed to strong external magnetic interference.
నిర్వహణ
The TURCK BIM-PST-AP6X-V1131 sensor is designed for low maintenance. Regular inspection is recommended to ensure continued reliable operation.
- శుభ్రపరచడం: Keep the sensor's active face clean and free from debris, dust, or excessive moisture. Use a soft, damp శుభ్రపరచడానికి వస్త్రం. రాపిడి క్లీనర్లు లేదా ద్రావకాలు ఉపయోగించవద్దు.
- కేబుల్ మరియు కనెక్టర్ తనిఖీ: Periodically check the M8 connector and cable for signs of wear, damage, or corrosion. Ensure the connection is secure.
- మౌంటు భద్రత: Verify that the sensor and its KLP-80 mounting bracket remain securely fastened to the cylinder. Vibrations can loosen mounting hardware over time.
- పర్యావరణ తనిఖీ: Ensure the operating environment remains within the sensor's specified temperature and humidity limits.
No internal user-serviceable parts are present. Do not attempt to open or repair the sensor.
ట్రబుల్షూటింగ్
If the sensor is not functioning as expected, consider the following common issues and solutions:
| సమస్య | సాధ్యమైన కారణం | పరిష్కారం |
|---|---|---|
| Sensor not detecting target / No output |
|
|
| అడపాదడపా గుర్తింపు |
|
|
| Sensor always ON/OFF (stuck state) |
|
|
If problems persist after attempting these solutions, contact Turck technical support.
స్పెసిఫికేషన్లు
| గుణం | విలువ |
|---|---|
| మోడల్ సంఖ్య | BIM-PST-AP6X-V1131 |
| టైప్ చేయండి | Magnetic Field Sensor, Inductive, Cylinder Position |
| అవుట్పుట్ రకం | 3-wire PNP |
| కనెక్షన్ | M8 పురుష కనెక్టర్ |
| Active Face | ముందు |
| ఆపరేటింగ్ వాల్యూమ్tage | 10-30 VDC |
| ప్రస్తుత వినియోగం | 200 mA (గరిష్టంగా) |
| తయారీదారు | టర్క్ |
| ASIN | B088C571JQ |
| మొదటి తేదీ అందుబాటులో ఉంది | మే 8, 2020 |
వారంటీ సమాచారం
Turck products are manufactured to high quality standards. For specific warranty terms and conditions, please refer to the official Turck warranty statement available on their website or contact their customer service. Typically, Turck provides a limited warranty against defects in materials and workmanship for a specified period from the date of purchase.
వారంటీ క్లెయిమ్ల కోసం మీ కొనుగోలు రుజువును ఉంచండి.
మద్దతు
For technical assistance, product inquiries, or warranty claims, please contact Turck customer support:
- Webసైట్: Visit the official Turck website for product datasheets, FAQs, and contact information. (e.g., www.turck.com)
- ఫోన్: Refer to the Turck webప్రాంతీయ సంప్రదింపు నంబర్ల కోసం సైట్.
- ఇమెయిల్: Use the contact forms or email addresses provided on the Turck webసైట్.
When contacting support, please have your product model number (BIM-PST-AP6X-V1131) and any relevant purchase details ready.
