1. పరిచయం
The Leviton DOS05-1LZ Decora Motion Sensor Light Switch is designed to provide automatic lighting control based on occupancy and motion detection. This 180° Passive Infrared (PIR) sensor can operate in either single-pole or 3-way configurations and does not require a neutral wire for installation, making it suitable for a wide range of residential applications. It is compatible with various load types including LED, CFL, Incandescent, Halogen, Magnetic Low Voltagఇ, ఎలక్ట్రానిక్ తక్కువ వాల్యూమ్tage, and motor loads up to ¼ HP. This device helps enhance convenience and energy efficiency by automatically turning lights on when motion is detected and off after a set period of inactivity.
The switch includes interchangeable faceplates in White, Ivory, and Light Almond to match your decor. It can also be used to comply with 2019 California Title 24, Part 6 Vacancy Control Device Requirements.
2. భద్రతా సమాచారం
WARNING: To avoid fire, shock, or death, always turn off power at the circuit breaker or fuse and test to ensure power is off before wiring. If you are unsure about any part of these instructions or are not comfortable or familiar with electrical wiring, contact a licensed electrician.
- This device is designed for use with copper or copper-clad wire only.
- Do not mount near a heat source or in drafty areas of the home, as temperature changes can affect sensor performance.
- Avoid mounting in motion-heavy areas where unintended motion will be within the sensor's field of view, unless adjusted for specific coverage.
3. ప్యాకేజీ విషయాలు
- One Leviton DOS05-1LZ Motion Sensor Light Switch
- Interchangeable faceplates (White, Ivory, Light Almond)
- సంస్థాపన సూచనలు
4. సంస్థాపన
4.1. అవసరమైన సాధనాలు
- ఫ్లాట్ హెడ్ స్క్రూడ్రైవర్
- ఫిలిప్స్ హెడ్ స్క్రూడ్రైవర్
- Electrician's pliers
- వైర్ స్ట్రిప్పర్
- ఎలక్ట్రికల్ టేప్
- Handheld voltagఇ టెస్టర్
- Properly sized wire connectors
4.2. ప్రీ-ఇన్స్టాలేషన్ దశలు
- సర్క్యూట్ బ్రేకర్ లేదా ఫ్యూజ్ వద్ద పవర్ ఆఫ్ చేయండి.
- Remove the existing switch plate and unscrew the old device from the wall box.
- Carefully pull the device out until you clearly see the wires.
- వాల్యూమ్ ఉపయోగించండిtage tester to ensure no power is present in the box.
- Carefully disconnect all wiring from the old device and remove it.
- Straighten and separate each wire. Ensure no exposed metal ends are touching.
4.3. Wiring the Motion Sensor Switch
The DOS05-1LZ can be wired with or without a neutral wire. Identify the wires in your wall box to determine the appropriate wiring configuration.
Figure 1: Leviton DOS05-1LZ Motion Sensor Switch with pre-stripped wires.
మూర్తి 2: వెనుకకు view of the switch showing wiring terminals and labels.
4.3.1. Wiring without a Neutral Wire (Ground Connection)
- Twist the green and yellow ground lead wire from the device and the green sleeve ground wire (if present) to the ground wire in the wall box. Secure with a properly sized wire connector and electrical tape.
- Connect the black lead wires from the device to the black wires (line and load) in the wall box. The line and load wires can be wired interchangeably. Secure with wire connectors and electrical tape.
- For DOS05-1LZ, cap off the red/yellow wire with a wire connector as it is only used for 3-way connections.
4.3.2. Wiring with a Neutral Wire
- Remove the green sleeve from the white wire on the product. Connect this white wire to the white neutral wire(s) in the wall box. Secure with a properly sized wire connector and electrical tape.
- Connect the green and yellow ground lead wire from the device to the ground wire in the wall box. Secure with a properly sized wire connector and electrical tape.
- Connect the black lead wires from the device to the black wires (line and load) in the wall box. The line and load wires can be wired interchangeably. Secure with wire connectors and electrical tape.
- For DOS05-1LZ, cap off the red/yellow wire with a wire connector as it is only used for 3-way connections.
Video 1: Detailed installation guide for Leviton Decora Occupancy and Vacancy Motion Sensor Light Switches (DOS05-1LZ included).
4.4. చివరి దశలు
- Gently bend the wires and push them into the wall box.
- Screw the sensor into the wall box.
- Install the wall plate (sold separately).
- సర్క్యూట్ బ్రేకర్ లేదా ఫ్యూజ్ వద్ద శక్తిని పునరుద్ధరించండి.
5. ఆపరేటింగ్ సూచనలు
5.1. ప్రాథమిక ఆపరేషన్
- స్వయంచాలక ఆన్/ఆఫ్: After a warm-up period (10-20 seconds), the lights will automatically turn on with the first motion detected. They will turn off after a set period of inactivity.
- మాన్యువల్ ఆన్/ఆఫ్: Press the lower part of the push pad to manually turn the lights on or off.
- Motion Detected Indicator: The red indicator light will flash anytime motion is detected.
- Light Off Indicator: The green indicator light illuminates when the light (load) it controls is off.
5.2 ప్రోగ్రామబుల్ సెట్టింగులు
The DOS05-1LZ offers three programmable settings: Timer, Sensitivity, and Ambient Light. These settings can be adjusted directly from the push pad without tools or removing the faceplate.
Figure 3: Adjust settings by pressing the push pad, no tools required.
5.2.1. ప్రోగ్రామింగ్ మోడ్లోకి ప్రవేశించడం
- Manually turn the light ON by pressing the push pad. The green LED will be off.
- Press the TOP and BOTTOM of the push pad simultaneously for 5 seconds.
- The green LED will turn on for 5 seconds, then the red LED will blink once, and the green LED will blink three times. This indicates you are in Programming Mode, currently in the Timer Setting (Option 3, 10 minutes, default).
గమనిక: Programming Mode will time out after 30 seconds if no activity is detected, and changes will not be saved.
5.2.2. Changing Settings and Options
- To change the Setting (Timer, Sensitivity, Ambient Light): Press the TOP of the push pad. The red LED will blink to indicate the setting number (1 blink for Timer, 2 for Sensitivity, 3 for Ambient Light).
- To change the Setting Option (e.g., 1 minute, 5 minutes for Timer): Press the BOTTOM of the push pad. The green LED will blink to indicate the option number (1 blink for Option 1, 2 for Option 2, etc.).
5.2.3. Timer Setting (Setting 1)
Adjusts the duration the light remains ON after motion was last detected.
- Option 1: 1 Minute
- Option 2: 5 Minutes
- Option 3: 10 Minutes (Default)
- Option 4: 20 Minutes
5.2.4. Sensitivity Setting (Setting 2)
Adjusts the device's sensitivity to motion, affecting the detection range.
- Option 1: Low (50% range)
- Option 2: Medium (Default)
- Option 3: High (Maximum coverage area)
Figure 4: 180° PIR detection range, up to 900 sq. ft. Customize sensing range/coverage area for your application.
5.2.5. Ambient Light Setting (Setting 3 - Occupancy Sensors Only)
Adjusts the device's sensitivity to natural light, preventing lights from turning on if there is ample natural light in the room.
- Option 1: Low Light Level
- Option 2: Medium Light Level (Default)
- Option 3: High/Brightest Light Level
- Option 4: Disabled (Light turns on for all light levels regardless of ambient light)
5.3. Temporary Modes
5.3.1. టెస్ట్ మోడ్
Turns on the light for 5 seconds every time motion is detected. Useful for testing field of view coverage after installation.
- పనిచేయటానికి: Press and hold the TOP of the push pad for 5 seconds. The red light will blink once every 2 seconds.
- బయటకు పోవుటకు: Press the TOP or BOTTOM of the push pad, or it will automatically time out after 2 minutes.
5.3.2. Temporary Bypass Mode (Occupancy Sensors Only)
Ignores motion, preventing detection and keeping the light or load off. Useful when you want a room to remain dark even if there is motion (e.g., watching a movie).
- సక్రియం చేయడానికి: Press and hold the BOTTOM of the push pad for 5 seconds. The green light will double flash every 2 seconds.
- బయటకు పోవుటకు: Press the TOP or BOTTOM of the push pad.
Video 2: How to Program the Leviton Decora Occupancy and Vacancy Motion Sensor Light Switches.
6. ట్రబుల్షూటింగ్
| సమస్య | సాధ్యమైన కారణం / పరిష్కారం |
|---|---|
| Lights do not operate with push pad and RED indicator does not blink when motion is present. | Verify wiring connections to sensor. |
| Lights do not switch ON when motion is detected (DOS05). |
|
| Lights always stay ON. |
|
| Lights do not turn ON (DVS05). |
|
7. స్పెసిఫికేషన్లు
- మోడల్ సంఖ్య: DOS05-1LZ
- ఆపరేషన్ మోడ్: ఆన్-ఆఫ్-ఆన్
- ప్రస్తుత రేటింగ్: 2 Amps
- ఆపరేటింగ్ వాల్యూమ్tage: 120 వోల్ట్లు
- సంప్రదింపు రకం: సాధారణంగా తెరవండి
- కనెక్టర్ రకం: క్రింప్
- టెర్మినల్: బ్లేడ్
- అంశం కొలతలు (L x W x H): 1.38 x 1.73 x 4.13 అంగుళాలు
- సర్క్యూట్ రకం: 3-మార్గం
- యాక్యుయేటర్ రకం: పుష్ బటన్
- సంప్రదింపు పదార్థం: ఫాస్ఫర్ కాంస్య
- అంతర్జాతీయ రక్షణ రేటింగ్: IP54
- స్థానాల సంఖ్య: 1
- తక్కువ ఉష్ణోగ్రత రేటింగ్: 70 డిగ్రీల ఫారెన్హీట్
- అధిక ఉష్ణోగ్రత రేటింగ్: 100 డిగ్రీల ఫారెన్హీట్
- నియంత్రిక రకం: పుష్ బటన్
- నియంత్రణ పద్ధతి: టచ్
- కనెక్టివిటీ ప్రోటోకాల్: X-10
- రంగు: White/Ivory/Light Almond
- వాట్tage: 600 వాట్స్
- అనుకూల పరికరాలు: LED, CFL, Incandescent, Halogen, Magnetic Low Voltagఇ, ఎలక్ట్రానిక్ తక్కువ వాల్యూమ్tage, Motor loads
- శక్తి మూలం: కార్డెడ్ ఎలక్ట్రిక్
- వస్తువు బరువు: 4.6 ఔన్సులు
8. నిర్వహణ
To maintain optimal performance and appearance of your Leviton Motion Sensor Light Switch, follow these simple guidelines:
- శుభ్రపరచడం: ఒక మృదువైన ఉపయోగించండి, డిamp cloth to clean the surface of the switch. Avoid abrasive cleaners, solvents, or harsh chemicals, as these can damage the finish or internal components.
- తనిఖీ: స్విచ్ దెబ్బతినడం, వదులుగా ఉన్న కనెక్షన్లు లేదా అసాధారణ ఆపరేషన్ సంకేతాలు ఉన్నాయా అని కాలానుగుణంగా తనిఖీ చేయండి. ఏవైనా సమస్యలు గమనించినట్లయితే, సర్క్యూట్ బ్రేకర్ వద్ద పవర్ ఆఫ్ చేసి, అర్హత కలిగిన ఎలక్ట్రీషియన్ను సంప్రదించండి.
- లెన్స్ కేర్: Keep the sensor lens clean and free from dust or obstructions to ensure accurate motion detection.
- పర్యావరణ పరిగణనలు: Ensure the switch is not exposed to excessive moisture or extreme temperatures beyond its operating range, as this can affect its lifespan and functionality.
9. వారంటీ మరియు మద్దతు
This Leviton Motion Sensor Light Switch (DOS05-1LZ) comes with a 5-సంవత్సరం పరిమిత వారంటీ. For warranty claims, technical support, or further assistance, please contact Leviton customer service or visit their official webసైట్. వారంటీ ధ్రువీకరణ కోసం మీ కొనుగోలు రుజువును ఉంచండి.
