1. పరిచయం
The LILYGO T5 4.7 Inch E-Paper V2.3 ESP32-S3 Development Driver Board is a versatile module designed for various development and display applications. It integrates an ESP32-S3 microcontroller with Wi-Fi and Bluetooth V5.0 connectivity, paired with a low-power 4.7-inch e-paper display. This manual provides essential information for setting up and operating your device.
2 కీ ఫీచర్లు
- MCU: ESP32-S3-WROOM-1-N1 6R8
- వైర్లెస్ కనెక్టివిటీ: Wi-Fi, Bluetooth V5.0
- ప్రదర్శన: 4.7-inch Ultra-low Power E-paper (Driver IC: ED047TC1)
- ప్రదర్శన రిజల్యూషన్: 540 x 960 pixels, 16 Gray levels
- మెమరీ: 16MB ఫ్లాష్, 8MB PSRAM
- అదనపు ఫీచర్లు: Support TF card, PCF8563 RTC, Battery capacity detection
- కొలతలు: 4.68 x 2.44 x 0.31 అంగుళాలు
3. ప్యాకేజీ విషయాలు
Image showing the LILYGO T5 4.7 Inch E-Paper V2.3 ESP32-S3 Development Board along with its accessories.
The development board and accessories are shown inside a protective plastic case.
- 1 x LILYGO T5 4.7 Inch E-Paper V2.3 ESP32-S3 Development Board
- 1 x GROVE Interface Cable
- 1 x పవర్ కేబుల్
- 1 x Female Pin 2*20p Header
4. హార్డ్వేర్ ఓవర్view
టాప్ view of the LILYGO T5-4.7-S3 board, highlighting the ESP32-S3 module, USB-C port, and various connectors.
The 4.7-inch E-Paper display, showcasing its low power consumption and high readability.
Dimensions of the LILYGO T5-4.7-S3 board.
Detailed pinout diagram of the LILYGO T5-4.7-S3 E-Paper board.
The board features a Type-C USB port for power and data transfer, a JST-GH 1.25mm 2-pin battery interface, and GPIO pin extension definitions. It also reserves a JST-SH 1.0mm 4-pin interface for STEMMA QT/Qwiic compatibility.
5. సెటప్ మరియు ప్రారంభించడం
5.1. Entering Download Mode
To flash new firmware onto the board, you need to enter download mode. This typically involves a sequence of button presses:
- Connect the board to your computer via the USB-C cable.
- నొక్కండి మరియు పట్టుకోండి బూట్ బటన్.
- While holding BOOT, briefly press the రీసెట్ చేయండి బటన్.
- విడుదల చేయండి రీసెట్ చేయండి బటన్.
- విడుదల చేయండి బూట్ బటన్.
The board is now in download mode and ready for firmware upload.
Video demonstrating how to unpack the product, connect the battery, and enter download mode (from 0:09 to 2:50).
5.2. Development Environments
The LILYGO T5-4.7-S3 board supports various development environments. Refer to the official documentation and community resources for detailed setup instructions for each.
- PlatformIO: Installation and burning firmware using PlatformIO IDE for VS Code.
- ఆర్డునో IDE: Installation and burning firmware using Arduino IDE.
- మైక్రోపైథాన్: Flashing MicroPython firmware onto the board.
- ESP-IDF: Setting up the ESP-IDF environment and flashing firmware.
Video demonstrating the process of flashing firmware using PlatformIO, Arduino IDE, and MicroPython/ESP-IDF (from 2:51 to 24:08 of the product introduction video, or the dedicated 'Flash Factory' video).
5.3. WiFi కాన్ఫిగరేషన్
To connect your device to a WiFi network, you can use the EspTouch app. Note that only 2.4GHz WiFi networks are supported.
- Download the EspTouch app on your smartphone (available for iOS and Android).
- Open the app and enter your 2.4GHz WiFi network name (SSID) and password.
- Ensure your LILYGO T5 board is in WiFi configuration mode (as indicated on its screen).
- Start the configuration process in the app. The board should connect to your WiFi network.
Once connected, the board can automatically synchronize time or display other network-dependent information.
Video demonstrating WiFi function and automatic time synchronization (from 0:58 to 1:20).
6. ప్రాథమిక ఆపరేషన్
The LILYGO T5-4.7-S3 board can display various information on its e-paper screen. Examples include a clock, WiFi status, battery level, and custom images. The onboard buttons can be programmed for custom functions, such as resetting the device or triggering specific display changes.
Video demonstrating automatic time synchronization and custom button functionality (from 1:10 to 1:50).
7. స్పెసిఫికేషన్లు
| ఫీచర్ | వివరాలు |
|---|---|
| MCU | ESP32-S3-WROOM-1-N1 6R8 |
| వైర్లెస్ కనెక్టివిటీ | Wi-Fi, Bluetooth V5.0 |
| ప్రదర్శన రకం | 4.7-inch E-Paper |
| డిస్ప్లే రిజల్యూషన్ | 540 x 960 పిక్సెల్లు |
| బూడిద స్థాయిలు | 16 |
| ఫ్లాష్ మెమరీ | 16 MB |
| PSRAM | 8 MB |
| RTC | PCF8563 |
| బ్యాటరీ ఇంటర్ఫేస్ | JST-GH 1.25mm 2-pin |
| కొలతలు (LxWxH) | 4.68 x 2.44 x 0.31 అంగుళాలు |
| వస్తువు బరువు | 2.88 ఔన్సులు |
8. ట్రబుల్షూటింగ్
విజువల్ ఎక్స్amples of common e-paper display characteristics.
- Screen Bubbles: Small bubbles in the corners of the screen are a characteristic of soft e-paper displays and are currently unavoidable.
- Yellowish Tint: This version of the ink screen may exhibit a yellowish color.
- Residual Images: The ink screen feature may cause residual images if partially refreshed for a long time. This is normal behavior for e-paper technology.
- కనెక్టివిటీ సమస్యలు: Ensure correct drivers are installed for the USB-C port. Verify the correct COM port is selected in your development environment.
- ఫర్మ్వేర్ అప్లోడ్ వైఫల్యం: Double-check that the board is in download mode before attempting to upload firmware.
9. మద్దతు & వనరులు
For further technical support, code examples, and community discussions, please refer to the official LILYGO GitHub repository:
