ఉత్పత్తి ముగిసిందిview
This manual provides essential information for the installation, operation, and maintenance of your new replacement carburetor. This carburetor is designed to be a direct replacement for Walbro style carburetors used in specific Echo and Shindaiwa models.
మూర్తి 1: ప్రధాన view of the carburetor, showing the primary body and an accompanying gasket. This image highlights the overall design and included components.
మూర్తి 2: ముందు view of the carburetor, detailing the air intake and throttle plate mechanism.
మూర్తి 3: వైపు view of the carburetor, illustrating the choke lever and fuel inlet port.
అనుకూలత
- Fits Echo models: సిఎస్-260 టి, సిఎస్-280 టి
- Fits Shindaiwa models: 269TS, 280TS
- Replaces Walbro style carburetors.
భద్రతా సమాచారం
Always prioritize safety when working with power tools and their components. Failure to follow these instructions may result in injury or damage to equipment.
- ఇంజిన్ ఉందని నిర్ధారించుకోండి ఆఫ్ మరియు చల్లని before beginning any work.
- ప్రమాదవశాత్తు ప్రారంభాన్ని నిరోధించడానికి స్పార్క్ ప్లగ్ వైర్ను డిస్కనెక్ట్ చేయండి.
- చేతి తొడుగులు మరియు కంటి రక్షణతో సహా తగిన వ్యక్తిగత రక్షణ పరికరాలు (PPE) ధరించండి.
- బాగా వెంటిలేషన్ ఉన్న ప్రదేశంలో పని చేయండి.
- Keep fuel and other flammable materials away from ignition sources.
సెటప్ మరియు ఇన్స్టాలేషన్
This section outlines the general steps for replacing your carburetor. Specific procedures may vary slightly depending on your exact equipment model. Refer to your equipment's original service manual for detailed instructions.
- తయారీ: Gather necessary tools (screwdrivers, wrenches, pliers, fuel line clamps). Ensure you have a clean workspace.
- ఎయిర్ ఫిల్టర్ అసెంబ్లీని తీసివేయండి: Carefully detach the air filter cover and remove the air filter element.
- ఇంధన లైన్లను డిస్కనెక్ట్ చేయండి: Identify and disconnect the fuel inlet and return lines from the old carburetor. Be prepared for minor fuel spills. Use clamps if necessary to prevent fuel leakage from the tank.
- Remove Throttle and Choke Linkages: Disconnect the throttle cable and choke rod from the old carburetor. Note their positions for reassembly.
- Unmount Old Carburetor: Remove the mounting nuts or bolts securing the carburetor to the engine manifold. Carefully pull the old carburetor away, ensuring any gaskets are removed.
- కొత్త గాస్కెట్లను ఇన్స్టాల్ చేయండి: Place the new gaskets (if supplied) in their correct positions between the engine manifold, insulator block (if present), and the new carburetor. Ensure they are properly aligned to prevent air leaks.
- మౌంట్ న్యూ కార్బ్యురేటర్: Position the new carburetor onto the mounting studs/bolts. Reattach the mounting nuts/bolts and tighten them securely, but do not overtighten.
- లింకేజీలను తిరిగి కనెక్ట్ చేయండి: Reattach the throttle cable and choke rod to the new carburetor. Verify smooth operation of both.
- ఇంధన లైన్లను తిరిగి కనెక్ట్ చేయండి: Reconnect the fuel inlet and return lines to the appropriate ports on the new carburetor. Ensure connections are secure and free of leaks.
- ఎయిర్ ఫిల్టర్ అసెంబ్లీని తిరిగి ఇన్స్టాల్ చేయండి: Replace the air filter element and air filter cover.
మూర్తి 4: టాప్ view of the carburetor, highlighting the idle speed and mixture adjustment screws. These screws are typically used for fine-tuning engine performance.
మూర్తి 5: దిగువన view of the carburetor, showing the fuel bowl and diaphragm area.
ఆపరేటింగ్ సూచనలు
After installation, the carburetor may require minor adjustments for optimal performance. This carburetor is designed to be a high-quality replacement and may come pre-adjusted for common applications.
ప్రారంభ ప్రారంభం
- Ensure the fuel tank is filled with the correct fuel mixture (if applicable for 2-stroke engines).
- Prime the carburetor if it has a primer bulb, until fuel is visible.
- Set the choke to the "full choke" position.
- Start the engine according to your equipment's manufacturer instructions.
- Once the engine fires or attempts to start, move the choke to the "half choke" or "run" position.
- Allow the engine to warm up for a few minutes before operating under load.
Carburetor Adjustment (if necessary)
Most small engine carburetors have two main adjustment screws: High-speed (H) and Low-speed (L) mixture screws, and an idle speed screw (T).
- Idle Speed (T): Adjusts the engine's RPM at idle. Turn clockwise to increase idle speed, counter-clockwise to decrease.
- Low-Speed Mixture (L): Controls the fuel-air mixture at idle and low RPMs. Adjust in small increments (1/8 turn) to achieve smooth idle without bogging down.
- High-Speed Mixture (H): Controls the fuel-air mixture at high RPMs. Adjust in small increments to achieve maximum power without sputtering or overheating.
గమనిక: Carburetor tuning can be complex. If you are unsure, consult a qualified technician or refer to specific tuning guides for your equipment model.
నిర్వహణ
Proper maintenance ensures the longevity and performance of your carburetor and equipment.
- ఇంధన నాణ్యత: Always use fresh, clean fuel. Stale or contaminated fuel is a primary cause of carburetor issues.
- ఇంధన ఫిల్టర్: Regularly inspect and replace the in-tank fuel filter to prevent debris from entering the carburetor.
- ఎయిర్ ఫిల్టర్: Keep the air filter clean and replace it as recommended by your equipment manufacturer. A dirty air filter can cause rich fuel mixtures and poor performance.
- నిల్వ: Before long-term storage, drain the fuel system or use a fuel stabilizer to prevent gum and varnish buildup in the carburetor.
ట్రబుల్షూటింగ్
This section provides common issues and their potential solutions related to carburetor performance.
| సమస్య | సాధ్యమైన కారణం | పరిష్కారం |
|---|---|---|
| ఇంజిన్ స్టార్ట్ అవ్వడం లేదు | No fuel, clogged fuel filter, incorrect choke setting, spark plug issue. | Check fuel level, replace fuel filter, adjust choke, inspect/replace spark plug. |
| ఇంజిన్ కఠినంగా/స్టాల్స్గా నడుస్తుంది | Dirty air filter, incorrect carburetor adjustment, stale fuel, vacuum leak. | Clean/replace air filter, adjust L/H screws, use fresh fuel, check for loose connections/gaskets. |
| Lack of power at high RPM | Incorrect H-screw adjustment, clogged fuel filter, restricted exhaust. | Adjust H-screw, replace fuel filter, check exhaust for blockages. |
| ఇంధన లీకేజీలు | Loose fuel lines, damaged gaskets, stuck float/needle valve. | Tighten connections, replace gaskets, inspect carburetor internals (if comfortable). |
If problems persist after attempting these solutions, it is recommended to seek assistance from a qualified service technician.
స్పెసిఫికేషన్లు
| బ్రాండ్ | C·T·S |
| మోడల్ సంఖ్య | CB-418 |
| Compatible Echo Models | CS-260T, CS-280T |
| Compatible Shindaiwa Models | 269TS, 280TS |
| భర్తీ చేస్తుంది | Walbro style carburetors |
| వస్తువు బరువు | 5.6 ఔన్సులు |
| ప్యాకేజీ కొలతలు | 5.91 x 5.12 x 1.57 అంగుళాలు |
| మూలం దేశం | చైనా |
| UPC | 783798638197 |
వారంటీ మరియు మద్దతు
For warranty information or technical support, please contact the manufacturer directly. Keep your purchase receipt as proof of purchase.
తయారీదారు: C·T·S
For further assistance, refer to the official product page or contact customer service via the details provided with your purchase.
