ఇన్స్ట్రక్షన్ మాన్యువల్

2.1. లక్షణాలు మరియు సామర్థ్యాలు

The SDL1020X-E is a high-performance programmable DC electronic load designed for a wide range of testing requirements. Key features include:

• Single channel operation with DC 150 V/30 A input, total power up to 200 W.
• 3.5-inch TFT-LCD display for clear data visualization.
• Supports 4 static modes: Constant Current (CC), Constant Voltage (CV), Constant Resistance (CR), and Constant Power (CP).
• Dynamic modes with adjustable frequencies: CC Dynamic mode up to 25 kHz, CP Dynamic mode up to 12.5 kHz, CV Dynamic mode up to 0.5 Hz.
• Resolution of 1 mV/1 mA for precise control.
• Adjustable current rise times from 0.001 A/µs to 2.5 A/µs.
• List function supporting up to 100 editable steps for complex test sequences.
• Remote communication via RS232, USB, and LAN interfaces.

2.2. సెటప్

To set up the SDL1020X-E Electronic Load:

1. అన్‌ప్యాకింగ్: Carefully remove the electronic load from its packaging. Inspect for any signs of shipping damage. Retain the packaging for future transport or storage.
2. పవర్ కనెక్షన్: Connect the provided power cord to the AC input on the rear panel of the device and then to a grounded AC power outlet. Ensure the voltage పరికరం యొక్క అవసరాలకు అనుగుణంగా ఉంటుంది.
3. లోడ్ కనెక్షన్: Connect the device under test (DUT) to the input terminals on the front panel. Observe correct polarity (+ and -).
4. ప్రారంభ పవర్ ఆన్: Press the power button on the front panel. The device will perform a self-test and display the main interface.
5. Remote Interface (Optional): If using remote control, connect the appropriate RS232, USB, or LAN cable to your computer and install the necessary drivers and software as per the detailed user manual.

మూర్తి 1: ముందు view of the Siglent SDL1020X-E Electronic Load, showing the display, control buttons, and input terminals.

చిత్రం 2: వెనుక view of the Siglent SDL1020X-E Electronic Load, highlighting the power input, fuse, and communication ports (RS232, LAN, USB).

2.3. Operating the Electronic Load

The SDL1020X-E offers various operating modes for different testing scenarios:

• స్థిర విద్యుత్తు (CC) మోడ్: Maintains a constant current draw from the DUT. Use the front panel controls to set the desired current value.
• స్థిరమైన సంtage (CV) మోడ్: స్థిరమైన వాల్యూమ్‌ను నిర్వహిస్తుందిtage across the DUT. Set the target voltage using the controls.
• స్థిర నిరోధకత (CR) మోడ్: Simulates a constant resistance load. The current drawn will vary with the voltage.
• స్థిరమైన పవర్ (CP) మోడ్: Maintains a constant power dissipation. The current and voltage will adjust to keep the power constant.
• డైనమిక్ మోడ్: Allows for rapid switching between two load levels (A/B) in CC, CV, CR, or CP modes. Configure the levels, dwell times, and rise/fall times.
• జాబితా మోడ్: Program a sequence of up to 100 steps with different load parameters and durations. This is ideal for automated testing and characterization.

Refer to the comprehensive user manual for detailed instructions on configuring each mode, setting parameters, and interpreting measurement results.

2.4. నిర్వహణ

To ensure the longevity and accuracy of your SDL1020X-E:

• శుభ్రపరచడం: బయటి భాగాన్ని శుభ్రం చేయడానికి మృదువైన, పొడి వస్త్రాన్ని ఉపయోగించండి. రాపిడి క్లీనర్లు లేదా ద్రావకాలను ఉపయోగించవద్దు.
• వెంటిలేషన్: Ensure adequate airflow around the device. Do not block the ventilation openings.
• నిల్వ: Store the device in a clean, dry environment when not in use.
• క్రమాంకనం: కొలత ఖచ్చితత్వాన్ని నిర్వహించడానికి అర్హత కలిగిన సిబ్బందిచే కాలానుగుణంగా క్రమాంకనం సిఫార్సు చేయబడింది.

2.5. Specifications (SDL1020X-E)

3.1. లక్షణాలు మరియు సామర్థ్యాలు

The SDS1202X-E is a powerful 200 MHz digital oscilloscope, utilizing Siglent's innovative SPO technology for superior signal fidelity and performance. Key features include:

• 200 MHz bandwidth, 2 channels.
• రియల్ టైమ్ లుampling rate up to 1 GSa/s.
• Record length up to 14 Mpts for capturing long waveforms.
• Minimum vertical input range of 500 µV/Div for observing small signals.
• Innovative digital trigger system with high sensitivity and low jitter.
• Waveform capture rate of 400,000 frames/sec (sequence mode) for capturing infrequent events.
• 256-level intensity grading display function and color temperature display mode.
• Standard serial bus triggering and decoding support for IIC, SPI, UART, RS232, CAN, and LIN.
• History waveform recording and sequential triggering for extended waveform analysis.
• 1M points FFT math function for high-frequency resolution signal spectra analysis.
• Hardware co-processor for fast and accurate measurements.

3.2. సెటప్

To set up the SDS1202X-E Digital Oscilloscope:

1. అన్‌ప్యాకింగ్: Carefully remove the oscilloscope and its accessories (probes, power cord) from the packaging. Inspect for any damage.
2. పవర్ కనెక్షన్: Connect the power cord to the AC input on the rear panel and then to a grounded AC power outlet.
3. ప్రోబ్ కనెక్షన్: Connect the oscilloscope probes to the input channels (CH1, CH2) on the front panel. Ensure a secure BNC connection.
4. ప్రోబ్ పరిహారం: Before making measurements, compensate the probes using the dedicated probe compensation signal output on the front panel. Adjust the trimmer on the probe until a flat-top square wave is displayed.
5. ప్రారంభ పవర్ ఆన్: Press the power button. The oscilloscope will boot up and display the waveform grid.

మూర్తి 3: ముందు view of the Siglent SDS1202X-E Oscilloscope, showing the display, control panel, and input channels.

చిత్రం 4: కోణీయ view of the Siglent SDS1202X-E Oscilloscope displaying a waveform, illustrating its user interface.

3.3. ఓసిల్లోస్కోప్‌ను నిర్వహించడం

The SDS1202X-E offers a wide array of functions for signal analysis:

• Vertical Controls: Adjust the vertical scale (Volts/Div) and position for each channel to fit the waveform on the screen.
• క్షితిజ సమాంతర నియంత్రణలు: Adjust the horizontal scale (Time/Div) and position to view different time segments of the waveform.
• ట్రిగ్గర్ సిస్టమ్: Configure the trigger type (Edge, Pulse, Video, Slope, etc.), source, and level to stabilize repetitive waveforms and capture specific events.
• కొలత విధులు: Use the built-in measurement tools to automatically calculate parameters like frequency, period, peak-to-peak voltage, RMS, etc.
• గణిత విధులు: Perform mathematical operations on waveforms, including addition, subtraction, multiplication, division, and FFT (Fast Fourier Transform) for frequency domain analysis.
• డీకోడింగ్: Utilize the serial bus decoding feature to analyze data from IIC, SPI, UART, RS232, CAN, and LIN protocols.
• నిల్వ: Save waveforms, setups, and screenshots to internal memory or a USB flash drive.

For detailed instructions on advanced features and specific measurement techniques, consult the full SDS1202X-E user manual.

3.4. నిర్వహణ

To maintain the performance and lifespan of your SDS1202X-E:

• శుభ్రపరచడం: ఒక మృదువైన ఉపయోగించండి, డిamp సి ని శుభ్రం చేయడానికి వస్త్రంasing and screen. Avoid harsh chemicals.
• ప్రోబ్ కేర్: Handle probes carefully. Avoid bending or stressing the cables. Store them properly when not in use.
• పర్యావరణం: Operate the oscilloscope within its specified temperature and humidity ranges. Avoid dusty or corrosive environments.
• ఫర్మ్‌వేర్ నవీకరణలు: తయారీదారుని కాలానుగుణంగా తనిఖీ చేయండి webసరైన పనితీరును మరియు కొత్త ఫీచర్లకు యాక్సెస్‌ను నిర్ధారించడానికి ఫర్మ్‌వేర్ అప్‌డేట్‌ల కోసం సైట్.

3.5. Specifications (SDS1202X-E)