BWT Aquameter HF Water Filter Meter 3/8" User Manual

1. పరిచయం

The BWT Aquameter HF 3/8" is a digital water meter designed for high-flow water systems, including main water lines, commercial kitchens, and multi-machine setups. It accurately tracks water consumption, displaying remaining filter capacity on an integrated LCD screen to facilitate timely filter replacements. This battery-powered unit (CR2032) offers flexible installation without the need for external wiring. It is compatible with BWT Bestmax and Besttaste filters, ensuring consistent water quality and equipment protection.

2. భద్రతా సమాచారం

• సంస్థాపన మరియు ఆపరేషన్ ముందు అన్ని సూచనలను జాగ్రత్తగా చదవండి.
• నీటి నష్టాన్ని నివారించడానికి అన్ని కనెక్షన్లు సురక్షితంగా మరియు లీకేజీ లేకుండా ఉన్నాయని నిర్ధారించుకోండి.
• Do not expose the Aquameter to extreme temperatures or direct sunlight.
• Only use the specified CR2032 battery for power.
• Installation should be performed by qualified personnel if you are unsure.
• Observe the flow direction arrow on the sensor during installation.

3. ప్యాకేజీ విషయాలు

ప్యాకేజీలో అన్ని భాగాలు ఉన్నాయని నిర్ధారించుకోండి:

• BWT Aquameter HF display unit
• Flow sensor (3/8" connections)
• కనెక్ట్ కేబుల్
• CR2032 battery (may be pre-installed or separate)
• సీలింగ్ దుస్తులను ఉతికే యంత్రాలు

Image 3.1: BWT Aquameter HF components.

4. ఉత్పత్తి ముగిసిందిview

The BWT Aquameter HF consists of two main parts: the display unit and the flow sensor.

4.1 Display Unit

The display unit features an LCD screen for showing remaining capacity and two control buttons:

• PROG బటన్: Used for entering programming mode and adjusting settings.
• తి రి గి స వ రిం చు బ ట ను: Used to reset the meter after a filter change or to confirm settings. A long press (min 3 sec) is typically required for reset.

4.2 Flow Sensor

The flow sensor measures the water passing through it. It has 3/8" connections and an arrow indicating the correct direction of water flow. The sensor connects to the display unit via a cable.

Image 4.1: BWT Aquameter HF display unit and flow sensor.

5. సెటప్

5.1 బ్యాటరీ ఇన్‌స్టాలేషన్

1. Locate the battery compartment on the back of the display unit.
2. కంపార్ట్మెంట్ కవర్ తెరవండి.
3. Insert one CR2032 battery, ensuring correct polarity (+/-).
4. బ్యాటరీ కంపార్ట్‌మెంట్ కవర్‌ను సురక్షితంగా మూసివేయండి.

5.2 Flow Sensor Installation

1. Identify the water line where the Aquameter will be installed. Ensure the water supply is turned off before proceeding.
2. Cut the water line and prepare the 3/8" connections.
3. Insert the sealing washers into the sensor connections.
4. Connect the flow sensor into the water line, ensuring the arrow on the sensor points in the direction of water flow. Tighten connections securely to prevent leaks.
5. Connect the cable from the flow sensor to the designated port on the display unit.

5.3 డిస్ప్లే యూనిట్‌ను మౌంట్ చేయడం

The display unit can be mounted on a wall or cabinet using appropriate fasteners (not included). Choose a location that is easily accessible for viewing and programming.

చిత్రం 5.1: ఉదాample installation of the Aquameter display unit.

Image 5.2: Aquameter and filter installed in an under-sink setup.

5.4 ప్రారంభ ప్రోగ్రామింగ్

After installation, program the Aquameter according to your specific filter and water hardness settings. Refer to your filter's documentation for its rated capacity.

1. నొక్కండి మరియు పట్టుకోండి PROG button until the display enters programming mode.
2. ఉపయోగించండి PROG button to cycle through settings (e.g., total filter capacity in liters).
3. ఉపయోగించండి రీసెట్ చేయండి button to adjust the value for the selected setting.
4. Repeat for all necessary settings, such as water hardness if your filter requires this input.
5. Once all settings are configured, press and hold the PROG సేవ్ చేయడానికి మరియు ప్రోగ్రామింగ్ మోడ్ నుండి నిష్క్రమించడానికి మళ్ళీ బటన్.

6. ఆపరేటింగ్

6.1 డిస్ప్లేను చదవడం

The LCD display shows the remaining capacity of your water filter in liters. As water flows through the sensor, this value will decrease. When the capacity reaches a low level or zero, it indicates that a filter change is due.

6.2 Resetting the Meter

After replacing your water filter, the Aquameter must be reset to its full capacity. To do this:

1. Ensure the new filter is installed correctly.
2. నొక్కండి మరియు పట్టుకోండి రీసెట్ చేయండి కనీసం 3 సెకన్ల పాటు బటన్.
3. The display will show the full programmed capacity, indicating a successful reset.

7. నిర్వహణ

7.1 ఫిల్టర్ భర్తీ

Replace your water filter cartridge when the Aquameter indicates that the remaining capacity is low or depleted. Follow the specific instructions provided with your BWT filter cartridge for replacement procedures.

7.2 బ్యాటరీ భర్తీ

When the display becomes dim or stops functioning, it is time to replace the CR2032 battery. Follow the battery installation steps in Section 5.1.

7.3 శుభ్రపరచడం

Wipe the exterior of the display unit with a soft, damp గుడ్డ. రాపిడి క్లీనర్లు లేదా ద్రావకాలు ఉపయోగించవద్దు.

8. ట్రబుల్షూటింగ్

• ప్రదర్శన ఖాళీగా ఉంది: Check or replace the CR2032 battery. Ensure the battery is inserted with correct polarity.
• No flow reading: Verify that the flow sensor is installed correctly with the arrow pointing in the direction of water flow. Check for any blockages in the water line or sensor. Ensure the sensor cable is securely connected to the display unit.
• తప్పు రీడింగ్‌లు: Re-check the programming settings (filter capacity, water hardness) as described in Section 5.4. Ensure the correct filter type is being used for the programmed settings.
• Leaks at connections: Turn off water supply immediately. Check all connections for proper tightening and ensure sealing washers are correctly seated and not damaged.

9. స్పెసిఫికేషన్లు

10. వారంటీ

For specific warranty details regarding your BWT Aquameter HF, please refer to the warranty information provided with your purchase documentation or contact your authorized BWT dealer. Keep your proof of purchase for warranty claims.

11. మద్దతు

Should you require technical assistance, have questions about installation, or need further information about BWT products, please visit the official BWT website or contact your local BWT distributor. You can find more information at www.bwt.com.